Discrete element modelling of tillage forces and soil movement of a one-third scale mouldboard plough

In Australia there is renewed interest in mouldboard ploughing to improve crop yields of non-wetting sandy soils. Burying the top layer of non-wetting soil and bringing to the surface soil that has better water holding capacity is beneficial for plant growth. To improve the effectiveness of the ploughing it is essential to: (1) optimise the tillage forces and (2) understand the soil inversion and burial process. Recent studies show that Discrete Element Modelling (DEM) has the potential to predict both tillage forces and soil movement of tillage implements. In this study a one-third scale mouldboard plough was constructed and tested in a soil bin where draught force, vertical force and soil movement were measured. A comparison of the measured and simulated draught and downward vertical forces showed a close agreement. A procedure was developed to compare soil movement, percentage burial of top soil and forward soil movement of the soil bin tests and the DEM simulations. The results showed similar trends and patterns for both the percentage of the top soil buried to various tillage depths and the forward soil movement. Due to the larger than actual spherical particles used in the simulation the forward soil movement was greater for DEM. The DEM showed some particles moving below the tillage depth. This shows that further model development is needed with work recommended to look at using both clump particle shapes and smaller particle sizes to improve soil movement predictions.

[1]  I. Shmulevich,et al.  Interaction between soil and a wide cutting blade using the discrete element method , 2007 .

[2]  J. Arvidsson,et al.  Comparing measured with simulated vertical soil stress under vehicle load: Are the measurements or the models wrong? , 2012 .

[3]  M. Nowak,et al.  The influence of pressure to the stresses inside the plough body , 2014 .

[4]  Itzhak Shmulevich,et al.  Evaluation of link-track performances using DEM , 2006 .

[5]  Chris Saunders,et al.  A force prediction model for mouldboard ploughs incorporating the effects of soil characteristic properties, plough geometric factors and ploughing speed , 2007 .

[6]  G. Richard,et al.  Modelling vertical and lateral weed seed movements during mouldboard ploughing with a skim-coulter , 2001 .

[7]  Salvatore Faugno,et al.  Numerical Simulation of Soil-plough Mouldboard Interaction , 2005 .

[8]  Chris Saunders,et al.  3D DEM tillage simulation: Validation of a hysteretic spring (plastic) contact model for a sweep tool operating in a cohesionless soil , 2014 .

[9]  Toshitsugu Tanaka,et al.  3-D DEM simulation of cohesive soil-pushing behavior by bulldozer blade , 2012 .

[10]  Richard J. Godwin,et al.  A Novel Approach to the Prediction of Tillage Tool Draught using a Standard Tine , 1997 .

[11]  Tavs Nyord,et al.  A discrete element model for soil–sweep interaction in three different soils , 2013 .

[12]  Josef Boxberger,et al.  Energy consumption in cultivating and ploughing with traction improvement system and consideration of the rear furrow wheel-load in ploughing , 2013 .

[13]  Chris Saunders,et al.  Three-dimensional discrete element modelling (DEM) of tillage: Accounting for soil cohesion and adhesion , 2015 .

[14]  A. O. Raji,et al.  Discrete element modelling of the deformation of bulk agricultural particulates , 1999 .

[15]  W. Arnold,et al.  Finite element simulation of moldboard–soil interaction , 2013 .

[16]  A. Mouazen,et al.  Modelling soil-sweep interaction with discrete element method , 2013 .

[17]  Chris Saunders,et al.  Defining the effect of sweep tillage tool cutting edge geometry on tillage forces using 3D discrete element modelling , 2015 .

[18]  K. Oost,et al.  Soil translocation resulting from multiple passes of tillage under normal field operating conditions , 2006 .

[19]  J. Keith Nisbett,et al.  Shigley's Mechanical Engineering Design , 1983 .

[20]  Bin Chen,et al.  DEM Simulation of Clod Crushing by Bionic Bulldozing Plate , 2008 .

[21]  Richard J. Godwin,et al.  Integrated soil tillage force prediction models , 2007 .

[22]  P. Eberhard,et al.  A discrete element model and its experimental validation for the prediction of draft forces in cohesive soil , 2014 .

[23]  Yuan Wang,et al.  Statistical analysis of sand grain/bed collision process recorded by high‐speed digital camera , 2008 .

[24]  Asma Sattar,et al.  Spatial distribution of soil forces on moldboard plough and draft requirement operated in silty-clay paddy field soil , 2015 .

[25]  J. Arvidsson,et al.  Comparing penetrometer and shear vane measurements with measured and predicted mouldboard plough draught in a range of Swedish soils , 2011 .

[26]  Chris Saunders,et al.  Three-dimensional discrete element modelling of tillage: Determination of a suitable contact model and parameters for a cohesionless soil , 2014 .

[27]  K. Araya,et al.  PM—Power and Machinery: A Three-stage Soil Layer Mixing Plough for the Improvement of Meadow Soil, Part 2: Soil Bin Experiments , 2001 .

[28]  Itzhak Shmulevich,et al.  Determination of discrete element model parameters required for soil tillage , 2007 .

[29]  Hifjur Raheman,et al.  Draught Prediction of Agricultural Implements using Reference Tillage Tools in Sandy Clay Loam Soil , 2006 .

[30]  J. Mak,et al.  Determining parameters of a discrete element model for soil–tool interaction , 2012 .

[31]  Sheng Li,et al.  Tillage translocation and tillage erosion in cereal-based production in Manitoba, Canada , 2007 .

[32]  Peter Eberhard,et al.  Prediction of draft forces in cohesionless soil with the Discrete Element Method , 2011 .