Assessment of role of morphology in gas permselectivity of membranes based on polypropylene/ethylene

Abstract This paper reports on the influence of morphology on gas permeability and selectivity of membranes made from polypropylene (PP)/ethylene vinyl acetate copolymer (EVA)/clay (OMMT) nanocomposites. The morphology was adjusted by variation in the EVA (25, 50 wt%), OMMT (0 and 5 wt%) and compatibilizer (PP-g-MAH) (0 and 5 wt%) contents. Gas permeation properties of membranes with different morphologies, were studied for pure CO 2 , O 2 and N 2 gases. X-ray diffraction (XRD) patterns showed no changes in crystalline structure of samples. TEM analysis confirmed high tendency of OMMT flacks for locating in the EVA phase. SEM results revealed that an increase in OMMT loading decreases the EVA droplet size ( D n ) in samples with droplet type morphology and increases continuity index of EVA (CCI) in the samples with co-continuous morphology. Changes in compatibilizer/OMMT ratio imposed a dual effect on the morphology of the system with respect to D n and CCI. A good correlation could be established between these morphological parameters with gas solubility parameters, gas permeability and CO 2 /N 2 as well as CO 2 /O 2 gas selectivity. Annealing was shown to change the morphology which in turn had a very strong influence on the membranes gas permeability behavior.

[1]  Q. Fu,et al.  Relation of free volume and barrier properties in the miscible blends of poly(vinyl alcohol) and nylon 6-clay nanocomposites film , 2009 .

[2]  A. E. Jansen,et al.  CO2 separation with polyolefin membrane contactors and dedicated absorption liquids: performances and prospects , 2002 .

[3]  Jahan B. Ghasemi,et al.  Preparation, optimization and characterization of novel ion exchange membranes by blending of chemically modified PVDF and SPPO , 2012 .

[4]  S. R. Teixeira,et al.  The role of the MMT on the morphology and mechanical properties of the PP/PET blends , 2008 .

[5]  J. Gérard,et al.  Morphology and gas barrier properties of polyethylene‐based nanocomposites , 2006 .

[6]  H. Khonakdar,et al.  An assessment of the role of morphology in thermal/thermo-oxidative degradation mechanism of PP/EVA/clay nanocomposites , 2010 .

[7]  M. Frounchi,et al.  Gas barrier properties of PP/EPDM blend nanocomposites , 2006 .

[8]  F. Faupel,et al.  Gas permeability and free volume in poly(amide-b-ethylene oxide)/ polyethylene glycol blend membranes , 2009 .

[9]  M. Sadeghi,et al.  The effect of urethane and urea content on the gas permeation properties of poly(urethane-urea) membranes , 2010 .

[10]  Edward L Cussler,et al.  Barrier membranes with different sizes of aligned flakes , 2005 .

[11]  K. Almdal,et al.  Phase continuity and inversion in polystyrene/poly(methyl methacrylate) blends , 2003 .

[12]  M. Barikani,et al.  The Effect of Hard Segments on the Gas Separation Properties of Polyurethane Membranes , 2007 .

[13]  Edward L Cussler,et al.  Polydisperse flakes in barrier films , 2004 .

[14]  Eric J. Amis,et al.  Influence of Layered Silicates on the Phase-Separated Morphology of PS−PVME Blends , 2003 .

[15]  Jennifer A. Lee,et al.  Influence of clay exfoliation on the physical properties of montmorillonite/polyethylene composites , 2002 .

[16]  H. Khonakdar,et al.  Rheology, Morphology and Estimation of Interfacial Tension of LDPE/EVA and HDPE/EVA Blends , 2005 .

[17]  Dukjoon Kim,et al.  Surface characterization of microporous polypropylene membranes modified by plasma treatment , 2001 .

[18]  H. Khonakdar,et al.  Morphology, rheology and dynamic mechanical properties of PP/EVA/clay nanocomposites , 2011 .

[19]  H. Khonakdar,et al.  Nonisothermal crystallization kinetics and determination of surface‐folding free energy of PP/EVA/OMMT nanocomposites , 2009 .

[20]  D. R. Paul,et al.  Formation of Co-continuous Structures in Melt-Mixed Immiscible Polymer Blends , 2003 .

[21]  D. R. Paul,et al.  Nanocomposites formed from polypropylene/EVA blends , 2009 .

[22]  H. Khonakdar,et al.  Dynamic mechanical properties and morphology of polyethylene/ethylene vinyl acetate copolymer blends , 2004 .

[23]  J. Gérard,et al.  Barrier properties of nylon 6-montmorillonite nanocomposite membranes prepared by melt blending: Influence of the clay content and dispersion state , 2007 .

[24]  R. N. Walters,et al.  Ethylene vinyl acetate/layered silicate nanocomposites prepared by a surfactant-free method: Enhanced flame retardant and mechanical properties , 2009 .

[25]  J. Lopez‐Cuesta,et al.  Effect of organoclay in an immiscible poly(ethylene terephtalate) waste/poly(methyl methacrylate) blend , 2010 .

[26]  M. Khayet,et al.  Gas transport properties of polypropylene/clay composite membranes , 2007 .

[27]  G. Choudalakis,et al.  Permeability of polymer/clay nanocomposites: A review , 2009 .

[28]  A. Hiltner,et al.  Barrier properties of polypropylene/polyamide blends produced by microlayer coextrusion , 2002 .

[29]  M. Sadeghi,et al.  Gas permeation properties of ethylene vinyl acetate-silica nanocomposite membranes , 2008 .

[30]  Behnam Ghalei,et al.  Characterization and gas permeability of polyurethane and polyvinyl acetate blend membranes with polyethylene oxide–polypropylene oxide block copolymer , 2012 .

[31]  H. Khonakdar,et al.  Correlation of morphological, dynamic mechanical, and thermal properties in compatibilized polypropy , 2012 .

[32]  Yingwu Luo,et al.  Co-Continuous Polymeric Nanostructures via Simple Melt Mixing of PS/PMMA. , 2009, Macromolecular rapid communications.

[33]  Sabu Thomas,et al.  Nonisothermal crystallisation, melting behavior and wide angle X-ray scattering investigations on linear low density polyethylene (LLDPE)/ethylene vinyl acetate (EVA) blends: effects of compatibilisation and dynamic crosslinking , 2005 .

[34]  Hong Tan,et al.  Clay locked phase morphology in the PPS/PA66/clay blends during compounding in an internal mixer , 2006 .

[35]  P. Dubois,et al.  Tailoring of Co‐Continuous Polymer Blend Morphology: Joint Action of Nanoclays and Compatibilizers , 2010 .