An Overview of Densification, Microstructure and Mechanical Property of Additively Manufactured Ti-6Al-4V — Comparison among Selective Laser Melting, Electron Beam Melting, Laser Metal Deposition and Selective Laser Sintering, and with Conventional Powder

This chapter begins with an introduction of the fundamental properties of Ti-6Al-4V, and its densification mechanism, typical microstructure and mechanical property achievable by conventional PM routes. This functions as a point of reference for the following discussion of the AM Ti-6Al-4V in terms of densification, microstructure, and mechanical property. The mostly popular laser-based AM techniques, namely selective laser melting (SLM), electron beam melting (EBM), laser metal deposition (LMD) and selective laser sintering (SLS), for the fabrication of Ti-6Al-4V have been overviewed based on an analysis of over 100 individual studies. Heat treatment is essential to most of the AM Ti-6Al-4V. Principles for selecting appropriate heat treatment for the AM Ti-6Al-4V are proposed based on martensite phase transformation and optimisation of mechanical properties. Oxygen impurity is an issue to most Ti materials and it is addressed in this chapter as well; counter measurements to mitigate oxygen have been suggested which involves the use of rare earth based materials.

[1]  Timothy P. Quinn,et al.  Effects of processing on microstructure and mechanical properties of a titanium alloy (Ti–6Al–4V) fabricated using electron beam melting (EBM), Part 2: Energy input, orientation, and location , 2013 .

[2]  Peter C. Collins,et al.  Direct laser deposition of in situ Ti–6Al–4V–TiB composites , 2003 .

[3]  G. Booysen,et al.  Additive manufacturing: Characterization of TI-6AI-4V alloy intended for biomedical application , 2010 .

[4]  Yang Hao,et al.  Compression fatigue behavior of Ti-6Al-4V mesh arrays fabricated by electron beam melting , 2012 .

[5]  C. Colin,et al.  As-Fabricated and Heat-Treated Microstructures of the Ti-6Al-4V Alloy Processed by Selective Laser Melting , 2011 .

[6]  F. Froes,et al.  Powder metallurgy of titanium alloys , 1990 .

[7]  Fábio Pinto da Silva,et al.  Medical design: Direct metal laser sintering of Ti–6Al–4V , 2010 .

[8]  Radovan Kovacevic,et al.  The design and production of Ti-6Al-4V ELI customized dental implants , 2008 .

[9]  R. Jaffee,et al.  THE EFFECTS OF CARBON, OXYGEN, AND NITROGEN ON THE MECHANICAL PROPERTIES OF TITANIUM AND TITANIUM ALLOYS , 1955 .

[10]  Heat treatment of Ti6Al4V produced by Selective Laser Melting: Microstructure and mechanical properties , 2012 .

[11]  Stefan Stübinger,et al.  Histological and biomechanical analysis of porous additive manufactured implants made by direct metal laser sintering: a pilot study in sheep. , 2013, Journal of biomedical materials research. Part B, Applied biomaterials.

[12]  Konrad Wissenbach,et al.  Ductility of a Ti‐6Al‐4V alloy produced by selective laser melting of prealloyed powders , 2010 .

[13]  Timothy P. Quinn,et al.  Effects of processing on microstructure and mechanical properties of a titanium alloy (Ti–6Al–4V) fabricated using electron beam melting (EBM), part 1: Distance from build plate and part size , 2013 .

[14]  David E. Cooper,et al.  E-Manufacturing for product improvement at Red Bull technology , 2012 .

[15]  Jianfeng Sun,et al.  Development of porous medical implant scaffolds via laser additive manufacturing , 2012 .

[16]  Christoph Leyens,et al.  Morphology, microstructure, and hardness of titanium (Ti-6Al-4V) blocks deposited by wire-feed additive layer manufacturing (ALM) , 2012 .

[17]  E. Brandl,et al.  Microstructure of additive layer manufactured Ti–6Al–4V after exceptional post heat treatments , 2012 .

[18]  D. Mynors,et al.  A three-dimensional finite element analysis of the temperature field during laser melting of metal powders in additive layer manufacturing , 2009 .

[19]  Ryan B. Wicker,et al.  Characterization of Ti–6Al–4V open cellular foams fabricated by additive manufacturing using electron beam melting , 2010 .

[20]  Zhigang Zak Fang,et al.  A critical review of mechanical properties of powder metallurgy titanium , 2010 .

[21]  C. Brice,et al.  Elevated temperature characterization of electron beam freeform fabricated Ti–6Al–4V and dispersion strengthened Ti–8Al–1Er , 2012 .

[22]  M. Dargusch,et al.  A transmission electron microscopy and three-dimensional atom probe study of the oxygen-induced fine microstructural features in as-sintered Ti–6Al–4V and their impacts on ductility , 2014 .

[23]  Christoph Leyens,et al.  Deposition of Ti–6Al–4V using laser and wire, part I: Microstructural properties of single beads , 2011 .

[24]  J. Kruth,et al.  A study of the microstructural evolution during selective laser melting of Ti–6Al–4V , 2010 .

[25]  Martine Wevers,et al.  Surface Modification of Ti6Al4V Open Porous Structures Produced by Additive Manufacturing , 2012 .

[26]  Mark Whittaker,et al.  Microstructural Characterization of a Prototype Titanium Alloy Structure Processed via Direct Laser Deposition (DLD) , 2011, Metallurgical and Materials Transactions B.

[27]  Peter C. Collins,et al.  Development of methods for the quantification of microstructural features in α + β-processed α/β titanium alloys , 2009 .

[28]  F. Sam.  Powder metallurgy of titanium alloys , 2013 .

[29]  Z. Fang,et al.  Hydrogen Sintering of Titanium to Produce High Density Fine Grain Titanium Alloys , 2012 .

[30]  S. L. Semiatin,et al.  Influence of heating and solidification conditions on the structure and surface quality of electron-beam melted Ti–6Al–4V ingots , 2007 .

[31]  Lars-Erik Rännar,et al.  Production of customized hip stem prostheses – a comparison between conventional machining and electron beam melting (EBM) , 2013 .

[32]  O. Ivasishin,et al.  Cost-Effective Blended Elemental Powder Metallurgy of Titanium Alloys for Transportation Application , 2000 .

[33]  Luca Facchini,et al.  Microstructure and mechanical properties of Ti‐6Al‐4V produced by electron beam melting of pre‐alloyed powders , 2009 .

[34]  Raymond F. Wegman,et al.  Titanium and Titanium Alloys , 2013 .

[35]  Y. Liu,et al.  In situ synchrotron radiation to understand the pathways for the scavenging of oxygen in commercially pure Ti and Ti–6Al–4V by yttrium hydride , 2013 .

[36]  F. Saito,et al.  Thermodynamic properties of oxygen in RE–O (RE=Gd, Tb, Dy, Er) solid solutions , 1998 .

[37]  P. Coelho,et al.  Characterization and in vivo evaluation of laser sintered dental endosseous implants in dogs. , 2012, Journal of biomedical materials research. Part B, Applied biomaterials.

[38]  M. Qian,et al.  Pressureless sintering of titanium and titanium alloys: sintering densification and solute homogenization , 2015 .

[39]  Philip B. Prangnell,et al.  Effect of build geometry on the β-grain structure and texture in additive manufacture of Ti6Al4V by selective electron beam melting , 2013 .

[40]  M. Qian,et al.  Impurity (Fe, Cl, and P)-Induced Grain Boundary and Secondary Phases in Commercially Pure Titanium (CP-Ti) , 2013, Metallurgical and Materials Transactions A.

[41]  R. Moat,et al.  A comparative study of laser direct metal deposition characteristics using gas and plasma-atomized Ti–6Al–4V powders , 2011 .

[42]  J. Beaman,et al.  Producing metal parts with selective laser sintering/hot isostatic pressing , 1998 .

[43]  A. A. Zadpoor,et al.  Fatigue behavior of porous biomaterials manufactured using selective laser melting. , 2013, Materials science & engineering. C, Materials for biological applications.

[44]  Christopher B. Williams,et al.  Additive manufacturing (AM) and nanotechnology: promises and challenges , 2013 .

[45]  Kyle Crosby,et al.  Titanium-6Aluminum-4Vanadium For Functionally Graded Orthopedic Implant Applications , 2013 .

[46]  Jaimie Tiley,et al.  Modeling the tensile properties in β-processed α/β Ti alloys , 2006 .

[47]  H. Imai,et al.  Powder metallurgy Ti–TiC metal matrix composites prepared by in situ reactive processing of Ti-VGCFs system , 2013 .

[48]  L. Murr,et al.  Compression deformation behavior of Ti-6Al-4V alloy with cellular structures fabricated by electron beam melting. , 2012, Journal of the mechanical behavior of biomedical materials.

[49]  H. J. Rack,et al.  Phase transformations during cooling in α+β titanium alloys , 1998 .

[50]  G. Thompson,et al.  Improving the performance of aerospace alloys , 2003 .

[51]  David L. Bourell,et al.  Direct laser freeform fabrication of high performance metal components , 1998 .

[52]  Robert F. Singer,et al.  In situ flaw detection by IR‐imaging during electron beam melting , 2012 .

[53]  Randall M. German,et al.  Review: liquid phase sintering , 2009 .

[54]  S. S. Al-Bermani,et al.  The Origin of Microstructural Diversity, Texture, and Mechanical Properties in Electron Beam Melted Ti-6Al-4V , 2010 .

[55]  B. Stucker,et al.  Microstructures and Mechanical Properties of Ti6Al4V Parts Fabricated by Selective Laser Melting and Electron Beam Melting , 2013, Journal of Materials Engineering and Performance.

[56]  Martine Wevers,et al.  Surface Roughness and Morphology Customization of Additive Manufactured Open Porous Ti6Al4V Structures , 2013, Materials.

[57]  Wei Zhang,et al.  Phase transformation dynamics during welding of Ti–6Al–4V , 2004 .

[58]  A. Mitchell,et al.  The Effect of Beam Oscillation Rate on Al Evaporation from a Ti-6Al-4V Alloy in the Electron Beam Melting Process , 1992 .

[59]  Moataz M. Attallah,et al.  Microstructure and tensile properties of selectively laser-melted and of HIPed laser-melted Ti–6Al–4V , 2013 .

[60]  Liu Wei,et al.  Evaluation of microstructural development in electron beam melted Ti-6Al-4V , 2012 .

[61]  Joakim Karlsson,et al.  Characterization and comparison of materials produced by Electron Beam Melting (EBM) of two different Ti-6Al-4V powder fractions , 2013 .

[62]  João Paulo C. Rodrigues,et al.  Rapid prototyping with high power fiber lasers , 2008 .

[63]  H. Maier,et al.  On the mechanical behaviour of titanium alloy TiAl6V4 manufactured by selective laser melting: Fatigue resistance and crack growth performance , 2013 .

[64]  W. D. Kingery,et al.  Introduction to Ceramics , 1976 .

[65]  C. Ju,et al.  A comparison of the fatigue behavior of cast Ti-7.5Mo with c.p. titanium, Ti-6Al-4V and Ti-13Nb-13Zr alloys. , 2005, Biomaterials.

[66]  M. Qian.  COLD COMPACTION AND SINTERING OF TITANIUM AND ITS ALLOYS FOR NEAR-NET-SHAPE OR PREFORM FABRICATION , 2010 .

[67]  G. Schaffer,et al.  Comparison of sintering of titanium and titanium hydride powders , 2010 .

[68]  S. L. Semiatin,et al.  The laser additive manufacture of Ti-6Al-4V , 2001 .

[69]  L. Murr,et al.  Microstructure and mechanical properties of open-cellular biomaterials prototypes for total knee replacement implants fabricated by electron beam melting. , 2011, Journal of the mechanical behavior of biomedical materials.

[70]  H Van Oosterwyck,et al.  The effect of pore geometry on the in vitro biological behavior of human periosteum-derived cells seeded on selective laser-melted Ti6Al4V bone scaffolds. , 2012, Acta biomaterialia.

[71]  Christoph Leyens,et al.  Deposition of Ti-6Al-4V using laser and wire, part II: Hardness and dimensions of single beads , 2011 .

[72]  R. German.  Sintering theory and practice , 1996 .

[73]  Emeka Nkenke,et al.  In vivo performance of selective electron beam-melted Ti-6Al-4V structures. , 2010, Journal of biomedical materials research. Part A.

[74]  Robert L. Mason,et al.  Fatigue Life of Titanium Alloys Fabricated by Additive Layer Manufacturing Techniques for Dental Implants , 2013, Metallurgical and Materials Transactions A.

[75]  Omer Van der Biest,et al.  Wire based additive layer manufacturing: Comparison of microstructure and mechanical properties of Ti–6Al–4V components fabricated by laser-beam deposition and shaped metal deposition , 2011 .

[76]  R. Singer,et al.  Cellular Ti-6Al-4V structures with interconnected macro porosity for bone implants fabricated by selective electron beam melting. , 2008, Acta biomaterialia.

[77]  Vamsi Krishna Balla,et al.  Laser processing of in situ synthesized TiB-TiN-reinforced Ti6Al4V alloy coatings , 2012 .

[78]  V. N. Zamkov,et al.  Microstructure, texture, and mechanical properties of electron-beam melted Ti–6Al–4V , 2003 .

[79]  Mika Salmi,et al.  Patient‐specific reconstruction with 3D modeling and DMLS additive manufacturing , 2012 .

[80]  V. L. Merkulovym.  [From unpublished materials]. , 1976, Nervnaia sistema.

[81]  Christoph Leyens,et al.  Mechanical properties of additive manufactured titanium (Ti–6Al–4V) blocks deposited by a solid-state laser and wire , 2011 .

[82]  Sheng-Hui Wang,et al.  Experimental studies on process-induced morphological characteristics of macro- and microstructures in laser consolidated alloys , 2011, Journal of Materials Science.

[83]  Li Yang,et al.  Compressive properties of Ti–6Al–4V auxetic mesh structures made by electron beam melting , 2012 .

[84]  M. Qian,et al.  TEM and XRD characterisation of commercially pure alpha-Ti made by powder metallurgy and casting , 2012 .

[85]  M. Dargusch,et al.  Impacts of trace carbon on the microstructure of as-sintered biomedical Ti-15Mo alloy and reassessment of the maximum carbon limit. , 2014, Acta biomaterialia.

[86]  F. Froes,et al.  Low cost titanium and developing applications , 2010 .

[87]  Kenji Sato,et al.  The influence of density and oxygen content on the mechanical properties of injection molded Ti-6Al-4V alloys , 2010 .

[88]  J. Beaman,et al.  Processing of titanium net shapes by SLS/HIP , 1999 .

[89]  I. Yadroitsava,et al.  Selective laser melting of Ti6Al4V alloy for biomedical applications: Temperature monitoring and microstructural evolution , 2014 .

[90]  Wei Sha,et al.  Application of artificial neural network for prediction of time-temperature-transformation diagrams in titanium alloys , 2000 .