Torsional guided wave attenuation in piping from coating, temperature, and large-area corrosion

Abstract Guided wave inspection is a recently commercialized approach for assessing the integrity of pipeline structures. It involves propagating a guided wave along a length of pipe and any abrupt change in the cross-section reflects a portion of the energy, indicating both the location and severity of damage from the detected signal. While not having the sensitivity of other inspection strategies, the technology is advantageous given its potential to rapidly inspect relatively long distances from a single sensor installation. One challenge with guided wave inspections is that general corrosion occurring over a large surface area, which is a common problem in many industries, may not reflect enough energy to be detected given the lack of an abrupt change in the cross section of the pipe. A potential solution for detecting and characterizing large-area corrosion is to measure the attenuation of the guided wave. Experiments were performed to measure the attenuation of the fundamental torsional guided wave over a 10–140 kHz frequency range for varying degrees of corrosion. Additionally, guided wave attenuation was measured on pipes with three different corrosion-protection coatings over a 10–60 kHz frequency range as a function of ambient temperature. By understanding the degree of attenuation as a function of both frequency and temperature in common pipeline configurations (coated and uncoated), it should be possible to approximate the degree of corrosion of in-service pipeline.

[1]  J. P. Joule Esq.,et al.  XVII. On the effects of magnetism upon the dimensions of iron and steel bars , 1847 .

[2]  Peter Cawley,et al.  Practical long range guided wave testing: applications to pipes and rails , 2003 .

[3]  N. S. Tzannes,et al.  Joule and Wiedemann Effects-The Simultaneous Generation of Longitudinal and Torsional Stress Pulses in Magnetostrictive Materials , 1966, IEEE Transactions on Sonics and Ultrasonics.

[4]  F Simonetti,et al.  A guided wave technique for the characterization of highly attenuative viscoelastic materials. , 2003, The Journal of the Acoustical Society of America.

[5]  P. Cawley,et al.  Rapid, Long Range Inspection of Chemical Plant Pipework Using Guided Waves , 2001 .

[6]  Christophe Bacon,et al.  Finite element modeling of torsional wave modes along pipes with absorbing materials , 2006 .

[7]  J. Rose.  Ultrasonic Waves in Solid Media , 1999 .

[8]  P. Balaguru,et al.  BOND BEHAVIOR OF CORRODED REINFORCEMENT BARS , 2000 .

[9]  Takafumi Noguchi,et al.  Evaluation of the bond properties between concrete and reinforcement as a function of the degree of reinforcement corrosion , 2002 .

[10]  Hegeon Kwun,et al.  Torsional guided-wave attenuation in coal-tar-enamel-coated, buried piping , 2004 .

[11]  J. Rose,et al.  Guided wave propagation and mode differentiation in hollow cylinders with viscoelastic coatings. , 2008, The Journal of the Acoustical Society of America.

[12]  E. Villari,et al.  Ueber die Aenderungen des magnetischen Moments, welche der Zug und das Hindurchleiten eines galvanischen Stroms in einem Stabe von Stahl oder Eisen hervorbringen , 1865 .

[13]  M. Lowe,et al.  The Reflection of Guided Waves From Circumferential Notches in Pipes , 1998 .

[14]  B. Auld,et al.  Acoustic fields and waves in solids , 1973 .

[15]  H. Kwun,et al.  The magnetostrictive sensor technology for long range guided wave testing and monitoring of structures , 2003 .

[16]  Bin Wu,et al.  Circumferential and longitudinal defect detection using T(0,1) mode excited by thickness shear mode piezoelectric elements. , 2006, Ultrasonics.

[17]  A. G. Roosenbrand,et al.  The reflection of the fundamental torsional mode from cracks and notches in pipes. , 2003, The Journal of the Acoustical Society of America.