Production of Al–20 wt.% Al2O3 composite powder using high energy milling

High energy ball milling was used to produce a nanostructured Al matrix composite reinforced by submicron α-alumina particles. Scanning electron microscopy analysis as well as tap and green density measurements were used to optimize the milling time needed for the completion of the mechanical milling process. Results show that addition of alumina particles as the reinforcement has a drastic effect on the size, morphology and pressability of the powder. Scanning electron microscopy shows that distribution of alumina particles in the Al matrix reaches a full homogeneity after steady state. This would increase the hardness of powder due to a nano-structured matrix and oxide dispersion strengthening.

[1]  G. K. Williamson,et al.  X-ray line broadening from filed aluminium and wolfram , 1953 .

[2]  Joseph R. Davis,et al.  Special Features of Structure Formation and Properties of Special High-Alloy Alloys of the Al – Si – Cu System , 2023, Metal Science and Heat Treatment.

[3]  R. Scattergood,et al.  Nanocrystalline Al–Mg alloy with ultrahigh strength and good ductility , 2006 .

[4]  Zhengdao Li,et al.  Nanostructured composite obtained by mechanically driven reduction reaction of CuO and Al powder mixture , 2000 .

[5]  C. Suryanarayana,et al.  Mechanical alloying and milling , 2004 .

[6]  L. Froyen,et al.  Microstructure and interface characteristics of B4C, SiC and Al2O3 reinforced Al matrix composites: a comparative study , 2001 .

[7]  José M. Torralba,et al.  Effect of mechanical alloying on the morphology, microstructure and properties of aluminium matrix composite powders , 2003 .

[8]  J. Torralba,et al.  The effects of mechanical alloying on the compressibility of aluminium matrix composite powder , 2003 .

[9]  E. Saiz,et al.  Wetting and strength issues at Al/α–alumina interfaces , 2003 .

[10]  Seyed Mojtaba Zebarjad,et al.  Dependency of physical and mechanical properties of mechanical alloyed Al–Al2O3 composite on milling time , 2007 .

[11]  K. Chattopadhyay,et al.  Microstructure and wear behaviour of aluminium alloys containing embedded nanoscaled lead dispersoids , 2004 .

[12]  E. Lavernia,et al.  Grain growth kinetics of a mechanically milled nanocrystalline Al , 2001 .

[13]  A. Miodownik,et al.  Microstructural changes in a mechanically alloyed Al-6.2Zn-2.5Mg-1.7Cu alloy (7010) with and without particulate SiC reinforcement , 1996 .

[14]  M. Hansen,et al.  Constitution of Binary Alloys , 1958 .

[15]  N. Lyakhov,et al.  Mechanochemical Grinding of Inorganic Oxides , 2003 .

[16]  Linan An,et al.  Synthesis and characterization of high volume fraction Al-Al2O3 nanocomposite powders by high-energy milling , 2006 .

[17]  J. Torralba,et al.  Mechanically alloyed AlN particle-reinforced Al-6061 matrix composites: Powder processing, consolidation and mechanical strength and hardness of the as-extruded materials , 2006 .

[18]  J. A. Rodríguez,et al.  Structure and properties of attrition-milled aluminium powder , 1997 .

[19]  J. Benjamin,et al.  Dispersion strengthened aluminum made by mechanical alloying , 1977 .

[20]  J. Cwajna,et al.  Characterization of reinforcement distribution in Al/(Al2O3)p composites obtained from composite powder , 2001 .

[21]  F. A. Khalid,et al.  Decomposition of process control agent during mechanical milling and its influence on displacement reactions in the Al-TiO2 system , 2005 .

[22]  Elisa Maria Ruiz-Navas,et al.  One step production of aluminium matrix composite powders by mechanical alloying , 2006 .

[23]  J. Torralba,et al.  Morphological and microstructural characterisation of low-alloying Fe powder obtained by mechanical attrition , 2003 .

[24]  Farghalli A. Mohamed,et al.  Particulate reinforced metal matrix composites — a review , 1991, Journal of Materials Science.

[25]  A. Simchi,et al.  Structural evolution during mechanical milling of nanometric and micrometric Al2O3 reinforced Al matrix composites , 2006 .

[26]  Zhiwei Li,et al.  Structural characterization of a mechanical alloyed Al–C mixture , 2006 .