Fatigue crack tolerance design for stainless steel by crack growth analysis

Abstract Fatigue damage of stainless steel was assessed by crack growth analysis. In order to characterize small crack initiation and growth, fatigue cracking behavior was observed by periodical replica investigations during a strain-controlled fatigue test in air at room temperature. It was shown that fatigue cracks with depths of several tens of micrometers were initiated in the early stage of the fatigue test and fatigue life could be estimated as a sum of the cycles for crack initiation of 100 μm in depth and those for growth to 3 mm. Use of the equivalent stress intensity factor allowed prediction of the crack growth for a given strain range. The crack growth analysis was also made to estimate the fatigue life prescribed by the design fatigue curve. Then, the growth prediction was made for thermal transient conditions to take advantage of the stress gradient in the depth direction and the relationship between the cumulative usage factor (CUF) and crack size was shown. It was concluded that fatigue damage accumulated in a stainless steel component can be estimated from an identified crack size, or the maximum CUF can be determined even if no crack was detected by the inspection.

[1]  Takao Nakamura,et al.  Evaluation of Environmental Fatigue in PWR PLM Activities , 2005 .

[2]  K. J. Miller,et al.  What is fatigue damage? A view point from the observation of low cycle fatigue process , 2005 .

[3]  Timothy D. Gilman,et al.  Application of Common Basis Stress Evaluation Methodology for Environmentally Assisted Fatigue for a Pressurized Water Reactor , 2013 .

[4]  Masayuki Kamaya,et al.  Assessment of thermal fatigue damage caused by local fluid temperature fluctuation (part I: characteristics of constraint and stress caused by thermal striation and stratification) , 2014 .

[5]  C. Gardin,et al.  Analytical prediction of crack propagation under thermal cyclic loading inducing a thermal gradient in the specimen thickness – Comparison with experiments and numerical approach , 2011 .

[6]  G. Glinka,et al.  Universal features of weight functions for cracks in mode I , 1991 .

[7]  Hermann Lang,et al.  Performance study of Ke factors in simplified elastic plastic fatigue analyses with emphasis on thermal cyclic loading , 2011 .

[8]  Masayuki Kamaya,et al.  Strain-based modeling of fatigue crack growth – An experimental approach for stainless steel , 2012 .

[9]  Makoto Higuchi.  Comparison of Environmental Fatigue Evaluation Methods in LWR Water , 2008 .

[10]  Masayuki Kamaya,et al.  Damage Assessment of Low-Cycle Fatigue by Crack Growth Prediction (Development of Growth Prediction Model and Its Application) , 2012 .

[11]  Ian Jones,et al.  THE EFFECT OF VARIOUS CONSTRAINT CONDITIONS IN THE FREQUENCY RESPONSE MODEL OF THERMAL STRIPING , 1995 .

[12]  A. Hirano,et al.  Final Proposal of Environmental Fatigue Life Correction Factor (Fen) for Structural Materials in LWR Water Environment , 2007 .

[13]  Baldev Raj,et al.  Thermal striping limits for components of sodium cooled fast spectrum reactors , 2009 .

[14]  Yibin Xue,et al.  Modeling fatigue small-crack growth with confidence - A multistage approach , 2010 .

[15]  Sven H. Reese,et al.  Sophisticated Procedures for Fatigue Evaluation in the Framework of German KTA Codes , 2013 .

[16]  M. Kamaya.  Environmental effect on fatigue strength of stainless steel in PWR primary water – Role of crack growth acceleration in fatigue life reduction , 2013 .

[17]  Masayuki Kamaya,et al.  A study on the evolution of crack networks under thermal fatigue loading , 2008 .

[19]  A. Fatemi,et al.  Fatigue Behavior of Stainless Steel 304L Including Strain Hardening, Prestraining, and Mean Stress Effects , 2010 .

[20]  Y. Takahashi,et al.  High-cycle fatigue behavior of type 316 stainless steel at 288 °C including mean stress effect , 2006 .

[21]  Grzegorz Glinka,et al.  Weight functions for a surface semi-elliptical crack in a finite thickness plate , 1991 .

[22]  M. Kamaya.  Assessment of thermal fatigue damage caused by local fluid temperature fluctuation (part II: crack growth under thermal stress) , 2014 .

[23]  Masayuki Kamaya,et al.  A Flaw Tolerance Concept for Plant Maintenance Using Virtual Fatigue Crack Growth Curve , 2013 .

[24]  Y. W. Kim,et al.  An explicit integral expression for the stress intensity factor of a semi-elliptic surface crack subjected to thermal transient loading , 1999 .

[25]  C. E. Jaske,et al.  Fatigue Design Criteria for Pressure Vessel Alloys , 1977 .

[26]  An analysis of stress intensity factor for thermal transient problems based on Green's function , 1994 .