Comparison of characterisation methods determining the thermal resistance of building components from onsite measurements

Abstract Reliable in situ thermal characterisation allows to study the actual thermal performance of building components rather than the theoretical performance calculated from thermal properties of the constituent material layers. The most generally accepted method for in situ thermal characterisation is the average method as described in ISO 9869. However, due to steady-state assumptions, the method's applicability can require long measurement periods and is often seasonally bounded. A correction for storage effects might shorten the required measurement time spans for the average method, but will not eliminate the seasonally bounded limitations. More advanced dynamic data analysis methods, such as regression modelling, ARX-modelling or stochastic grey-box modelling, can be used to overcome these difficulties. In this paper, a comparison between several semi-stationary and dynamic data analysis methods typically used for the thermal characterisation of building components from on-site measurements is made. Thereby, special attention is given to the reliability of the methods thermal resistance estimates when confronted with data sets of limited measurement time spans and different seasonal boundary conditions. First, the methods’ performances are assessed for simulated measurements of a south-facing insulated cavity wall in a moderate European climate. Subsequently, the performances are examined for actual measurement data of a similar test wall.

[1]  M. J. Jiménez,et al.  Analysis of capabilities and limitations of the regression method based in averages, applied to the estimation of the U value of building component tested in Mediterranean weather , 2012 .

[2]  P. H. Baker,et al.  PASLINK and dynamic outdoor testing of building components , 2008 .

[3]  Henrik Madsen,et al.  Thermal Performance Characterization using Time Series Data - IEA EBC Annex 58 Guidelines , 2015 .

[4]  M. R. Heras,et al.  Application of different dynamic analysis approaches to the estimation of the building component U value , 2009 .

[5]  An-Heleen Deconinck,et al.  Comparative assessment of in-situ thermal characterisation techniques , 2014 .

[6]  Arnold Janssens,et al.  Full scale test facilities for evaluation of energy and hygrothermal performances , 2011 .

[7]  Robert Lowe,et al.  Evidence for heat losses via party wall cavities in masonry construction , 2007 .

[8]  Christian Ghiaus,et al.  Physical parameters identification of walls using ARX models obtained by deduction , 2015 .

[9]  Lennart Ljung,et al.  System Identification: Theory for the User , 1987 .

[10]  M. J. Jiménez,et al.  Estimation of building component UA and gA from outdoor tests in warm and moderate weather conditions , 2008 .

[11]  Olaf Gutschker,et al.  Parameter identification with the software package LORD , 2008 .

[12]  Jan Carmeliet,et al.  CONSERVATIVE MODELLING OF THE MOISTURE AND HEAT TRANSFER IN BUILDING COMPONENTS UNDER ATMOSPHERIC EXCITATION , 2007 .

[13]  Peder Bacher,et al.  Setting up and validating a complex model for a simple homogeneous wall , 2014 .

[14]  Tadj Oreszczyn,et al.  Solid-wall U-values: heat flux measurements compared with standard assumptions , 2015 .

[15]  Jan Carmeliet,et al.  Brick Cavity Walls: A Performance Analysis Based on Measurements and Simulations , 2007 .

[16]  An-Heleen Deconinck,et al.  A Maximum Likelihood Estimation of the Thermal Resistance of a Cavity Wall from On-site Measurements , 2015 .

[17]  U. Norlén,et al.  Estimating thermal parameters of outdoor test cells , 1990 .

[18]  Sten Bay Jørgensen,et al.  Parameter estimation in stochastic grey-box models , 2004, Autom..

[19]  Gunnar Anderlind.  Multiple Regression Analysis of in situ Thermal Measurements — Study of an Attic Insulated with 800 mm Loose Fill Insulation , 1992 .

[20]  Sten Bay Jørgensen,et al.  A method for systematic improvement of stochastic grey-box models , 2004, Comput. Chem. Eng..

[21]  Steve Sharples,et al.  Full-scale measurements of convective energy losses from exterior building surfaces , 1984 .

[22]  Henrik Madsen,et al.  Identification of the main thermal characteristics of building components using MATLAB , 2008 .

[23]  Tadj Oreszczyn,et al.  Inferring the thermal resistance and effective thermal mass of a wall using frequent temperature and heat flux measurements , 2014 .