Study on local thermal–hydraulic performance and optimization of zigzag-type printed circuit heat exchanger at high temperature

Abstract High temperature heat exchanger is one of the most important components to transfer heat from the first loop to the second loop in the very high temperature reactor in nuclear energy application. In order to enhance the heat transfer performance, a mini-channel heat exchanger called printed circuit heat exchanger has attracted more attention in recent years. In this paper, the thermal–hydraulic performance of zigzag-type printed circuit heat exchanger with helium as the working fluid operating at the typical temperature of 900 °C in the very high temperature reactor is studied. It is found that the flow and temperature at high temperature cannot achieve a fully-developed condition due to the significant variation of thermal physical properties arisen from the large temperature difference. However, the non-dimensional velocity and temperature can become steady after the second pitch and is similar to the fluid flow behaviors at low temperature. Therefore the local Nusselt number and friction factor at high temperature can match well with those at low temperature when the Reynolds number is bigger than 900. With the increase of inclined angle, the heat transfer and pressure drop increase. It is recommended to put the channel with a larger inclined angle to the cold region when using the hybrid channels. The heat transfer enhancement method with inclined angles completely depends on the operating conditions.

[1]  M. Anderson,et al.  Development of a new forced convection heat transfer correlation for CO2 in both heating and cooling modes at supercritical pressures , 2011 .

[2]  David Southall.  Diffusion Bonding in Compact Heat Exchangers , 2009 .

[3]  Yasuyoshi Kato,et al.  Thermal-Hydraulic Characteristics of a Printed Circuit Heat Exchanger in a Supercritical CO2 loop , 2005 .

[4]  Kwang-Yong Kim,et al.  Comparative study on performance of a zigzag printed circuit heat exchanger with various channel shapes and configurations , 2013 .

[5]  Konstantin Nikitin,et al.  New printed circuit heat exchanger with S-shaped fins for hot water supplier , 2006 .

[6]  Y. Kato,et al.  Printed circuit heat exchanger thermal–hydraulic performance in supercritical CO2 experimental loop , 2006 .

[7]  Richard N. Christensen,et al.  Investigation of High-Temperature Printed Circuit Heat Exchangers for Very High Temperature Reactors , 2009 .

[8]  B. K. Hajek,et al.  Numerical study on thermal hydraulic performance of a Printed Circuit Heat Exchanger , 2013 .

[9]  Richard N. Christensen,et al.  Fabrication and design aspects of high-temperature compact diffusion bonded heat exchangers , 2012 .

[10]  Ting Ma,et al.  Study on thermal resistance distribution and local heat transfer enhancement method for SCO2–water heat exchange process near pseudo-critical temperature , 2015 .

[11]  Na Zhang,et al.  A novel nuclear combined power and cooling system integrating high temperature gas-cooled reactor with ammonia-water cycle , 2014 .

[12]  Yasuyoshi Kato,et al.  High performance printed circuit heat exchanger , 2007 .

[13]  Sai K. Mylavarapu,et al.  Design, Fabrication, Performance Testing, and Modeling of Diffusion Bonded Compact Heat Exchangers in a High-Temperature Helium Test Facility , 2011 .

[14]  Anton Moisseytsev,et al.  Preliminary issues associated with the next generation nuclear plant intermediate heat exchanger design , 2009 .

[15]  Kwang-Yong Kim,et al.  A Parametric Study of the Thermal-Hydraulic Performance of a Zigzag Printed Circuit Heat Exchanger , 2014 .

[16]  Piyush Sabharwall,et al.  Challenges in the development of high temperature reactors , 2013 .

[17]  Hee Cheon No,et al.  Physical model development and optimal design of PCHE for intermediate heat exchangers in HTGRs , 2012 .

[18]  Jan Fokkens,et al.  Promising designs of compact heat exchangers for modular HTRs using the Brayton cycle , 2008 .

[19]  S. K. Mylavarapu.  Development of Compact Heat Exchangers for Very High-Temperature Gas-Cooled Reactors , 2008 .

[20]  Michael L. Corradini,et al.  Heat Transfer of Supercritical Carbon Dioxide in Printed Circuit Heat Exchanger Geometries , 2011 .

[21]  Qiuwang Wang,et al.  Optimization of fin arrangement and channel configuration in an airfoil fin PCHE for supercritical CO2 cycle , 2014 .

[22]  Kwang-Yong Kim,et al.  Optimization of zigzag flow channels of a printed circuit heat exchanger for nuclear power plant application , 2012 .

[23]  Y. Kato,et al.  Heat transfer and pressure drop correlations of microchannel heat exchangers with S-shaped and zigzag fins for carbon dioxide cycles , 2007 .

[24]  Bengt Sundén,et al.  A Comparison of Some Heat Transfer Surfaces for Small Gas Turbine Recuperators , 2001 .

[25]  Mike Patterson,et al.  Design Option of Heat Exchanger for the Next Generation Nuclear Plant , 2010 .

[26]  Hee Cheon No,et al.  Thermal hydraulic performance analysis of the printed circuit heat exchanger using a helium test facility and CFD simulations , 2009 .

[27]  David Reay,et al.  Compact Heat Exchangers: Selection, Design and Operation , 2001 .

[28]  Chi-Chuan Wang,et al.  Simulation of Velocity Distribution and Pressure Drop in Every Channel in the Printed Circuit Heat Exchanger , 2013 .