Characterization of a new radiochromic three-dimensional dosimeter.

The development of intensity-modulated radiotherapy (IMRT) has created a clear need for a dosimeter that can accurately and conveniently measure dose distributions in three dimensions to assure treatment quality. PRESAGE is a new three dimensional (3D) dosimetry material consisting of an optically clear polyurethane matrix, containing a leuco dye that exhibits a radiochromic response when exposed to ionizing radiation. A number of potential advantages accrue over other gel dosimeters, including insensitivity to oxygen, radiation induced light absorption contrast rather than scattering contrast, and a solid texture amenable to machining to a variety of shapes and sizes without the requirement of an external container. In this paper, we introduce an efficient method to investigate the basic properties of a 3D dosimetry material that exhibits an optical dose response. The method is applied here to study the key aspects of the optical dose response of PRESAGE: linearity, dose rate dependency, reproducibility, stability, spectral changes in absorption, and temperature effects. PRESAGE was prepared in 1 x 1 x 4.5 cm3 optical cuvettes for convenience and was irradiated by both photon and electron beams to different doses, dose rates, and energies. Longer PRESAGE columns (2 x 2 x 13 cm3) were formed without an external container, for measurements of photon and high energy electron depth-dose curves. A linear optical scanning technique was used to detect the depth distribution of radiation induced optical density (OD) change along the PRESAGE columns and cuvettes. Measured depth-OD curves were compared with percent depth dose (PDD). Results indicate that PRESAGE has a linear optical response to radiation dose (with a root mean square error of -1%), little dependency on dose rate (-2%), high intrabatch reproducibility (< 2%), and can be stable (-2%) during 2 hours to 2 days post irradiation. Accurate PRESAGE dosimetry requires temperature control within 1 degrees C. Variations in the PRESAGE formulation yield corresponding variations in sensitivity, stability, and density. CT numbers in the range 100-470 were observed. In conclusion, the small volume studies presented here indicate PRESAGE to be a promising, versatile, and practical new dosimetry material with applicability for radiation therapy.

[1]  J. Gore,et al.  Radiation dose distributions in three dimensions from tomographic optical density scanning of polymer gels: II. Optical properties of the BANG polymer gel. , 1996, Physics in medicine and biology.

[2]  A Skretting,et al.  Measurement of the ferric diffusion coefficient in agarose and gelatine gels by utilization of the evolution of a radiation induced edge as reflected in relaxation rate images. , 1997, Physics in medicine and biology.

[3]  J C Gore,et al.  Effects of crosslinking and temperature on the dose response of a BANG polymer gel dosimeter. , 1997, Physics in medicine and biology.

[4]  J. Battista,et al.  Optical CT reconstruction of 3D dose distributions using the ferrous-benzoic-xylenol (FBX) gel dosimeter. , 1998, Medical physics.

[5]  S. Webb,et al.  An investigation into the dosimetry of a nine-field tomotherapy irradiation using BANG-gel dosimetry. , 1998, Physics in medicine and biology.

[6]  S Webb,et al.  Improving calibration accuracy in gel dosimetry. , 1998, Physics in medicine and biology.

[7]  M O Leach,et al.  Dynamics of polymerization in polyacrylamide gel (PAG) dosimeters: (II) modeling oxygen diffusion. , 1999, Physics in medicine and biology.

[8]  S. Webb,et al.  Dynamics of polymerization in polyacrylamide gel (PAG) dosimeters: (I) ageing and long-term stability. , 1999, Physics in medicine and biology.

[9]  B K Rutt,et al.  Polyvinyl alcohol-Fricke hydrogel and cryogel: two new gel dosimetry systems with low Fe3+ diffusion. , 2000, Physics in medicine and biology.

[10]  C De Wagter,et al.  An investigation of the chemical stability of a monomer/polymer gel dosimeter. , 2000, Physics in medicine and biology.

[11]  Steve Webb,et al.  Intensity-Modulated Radiation Therapy , 1996, International journal of radiation oncology, biology, physics.

[12]  J H Siewerdsen,et al.  High resolution gel-dosimetry by optical-CT and MR scanning. , 2001, Medical physics.

[13]  L. Lüdemann,et al.  Use of BANG polymer gel for dose measurements in a 68 MeV proton beam. , 2003, Medical physics.

[14]  C. Wuu,et al.  Determining optimal gel sensitivity in optical CT scanning of gel dosimeters. , 2003, Medical physics.

[15]  M. Oldham,et al.  Optical-CT gel-dosimetry I: basic investigations. , 2003, Medical physics.

[16]  Spectrophotometry of PRESAGE™ polyurethane dosimeters , 2004 .

[17]  Michelle Hilts,et al.  Image filtering for improved dose resolution in CT polymer gel dosimetry. , 2003, Medical physics.

[18]  M. Oldham,et al.  Optical-CT gel-dosimetry. II: Optical artifacts and geometrical distortion. , 2004, Medical physics.

[19]  M. Oldham,et al.  Evaluation of a 2D diode array for IMRT quality assurance. , 2004, Radiotherapy and oncology : journal of the European Society for Therapeutic Radiology and Oncology.

[20]  N. Krstajić,et al.  Optical CT scanning of PRESAGE TM polyurethane samples with a CCD-based readout system , 2004 .

[21]  J. Adamovics,et al.  A new approach to radiochromic three-dimensional dosimetry-polyurethane , 2004 .

[22]  M Oldham,et al.  Optical-CT scanning of polymer gels. , 2004, Journal of physics. Conference series.

[23]  J. Hanley,et al.  A clinical application of an automated phantom-film QA procedure for validation of IMRT treatment planning and delivery. , 2004, Medical dosimetry : official journal of the American Association of Medical Dosimetrists.