Environmental and human health risks of plastic composites can be reduced by optimizing manufacturing conditions

[1]  Brandon E. Boor,et al.  Emergency responder and public health considerations for plastic sewer lining chemical waste exposures in indoor environments. , 2021, Journal of hazardous materials.

[2]  Mohammad Najafi,et al.  Comparative Analysis of Environmental and Social Costs of Trenchless Cured-in-Place Pipe Renewal Method with Open-Cut Pipeline Replacement for Sanitary Sewers , 2020 .

[3]  Brandon E. Boor,et al.  An emerging mobile air pollution source: outdoor plastic liner manufacturing sites discharge VOCs into urban and rural areas. , 2020, Environmental science. Processes & impacts.

[4]  J. Youngblood,et al.  Influence of aggressive environmental aging on mechanical and thermo-mechanical properties of Ultra Violet (UV) Cured in Place Pipe liners , 2020 .

[5]  John C. Matthews,et al.  Environmental Impact Assessment of the Fabrication of Pipe Rehabilitation Materials , 2020 .

[6]  Parastou Kharazmi,et al.  Experimental assessment of the state of the lining materials used in the rehabilitation of sewers in residential buildings , 2019 .

[7]  Brandon E. Boor,et al.  Considerations for emission monitoring and liner analysis of thermally manufactured sewer cured-in-place-pipes (CIPP). , 2019, Journal of hazardous materials.

[8]  J. Youngblood,et al.  Evaluation of the physical, chemical, mechanical, and thermal properties of steam-cured PET/polyester cured-in-place pipe , 2019, Journal of Composite Materials.

[9]  Brandon E. Boor,et al.  In vitro toxicity assessment of emitted materials collected during the manufacture of water pipe plastic linings , 2019, Inhalation toxicology.

[10]  J. Youngblood,et al.  Outdoor manufacture of UV-Cured plastic linings for storm water culvert repair: Chemical emissions and residual. , 2019, Environmental pollution.

[11]  C. Jafvert,et al.  Critical Review: Surface Water and Stormwater Quality Impacts of Cured‐In‐Place Pipe Repairs , 2018 .

[12]  John C. Matthews,et al.  Evaluation of testing methods for tracking CIPP liners’ life-cycle performance , 2018 .

[13]  Brandon E. Boor,et al.  Worksite Chemical Air Emissions and Worker Exposure during Sanitary Sewer and Stormwater Pipe Rehabilitation Using Cured-in-Place-Pipe (CIPP) , 2017 .

[14]  E. Allouche,et al.  Thermo-Cyclic Degradation Evaluation of Sewer CIPP Resin by ASTM Standard Tests and Raman Spectroscopy , 2017 .

[15]  Bankim Chandra Ray,et al.  Effect of post-curing on thermal and mechanical behavior of GFRP composites , 2015 .

[16]  A. Whelton,et al.  Stormwater chemical contamination caused by cured-in-place pipe (CIPP) infrastructure rehabilitation activities. , 2014, Environmental science & technology.

[17]  Donna Dawson,et al.  Cured-in-place Pipe: Trenchless Trends , 2012 .

[18]  C. Lungu,et al.  Influence of temperature on styrene emission from a vinyl ester resin thermoset composite material. , 2011, The Science of the total environment.

[19]  J. E. McAlvin.  Green Composites Through the Use of Styrene-Free Resins and Unsaturated Polyesters Derived from Renewable and Recycled Raw Materials , 2011 .

[20]  T. Hanemann,et al.  Polymerization conditions influence on the thermomechanical and dielectric properties of unsaturated polyester-styrene-copolymers , 2010 .

[21]  Paul Compston,et al.  Mechanical properties and styrene emission levels of a UV-cured glass-fibre/vinylester composite , 2008 .

[22]  K. Grudzinski,et al.  Time-temperature-transformation (TTT) cure diagram for EPY® epoxy system , 2007 .

[23]  Y. Grohens,et al.  Mechanical Properties of Composites Based on Low Styrene Emission Polyester Resins for Marine Applications , 2006 .

[24]  L. J. Lee,et al.  Effect of dual-initiator on low temperature curing of unsaturated polyester resins , 2004 .

[25]  L. J. Lee,et al.  Control of shrinkage and residual styrene of unsaturated polyester resins cured at low temperatures: I. Effect of curing agents , 2003 .

[26]  J. Bare.  Traci , 2002 .

[27]  P. Pfäffli,et al.  Styrene and styrene oxide concentrations in the air during the lamination process in the reinforced plastics industry. , 1979, Scandinavian journal of work, environment & health.

[28]  A. Thomas,et al.  The Use of Peroxyketals as Initiators for Curing Unsaturated Polyester Sheet Molding Compound , 1979 .