An atomic force microscopy-based method for line edge roughness measurement

With the constant decrease of semiconductor device dimensions, line edge roughness (LER) becomes one of the most important sources of device variability and needs to be controlled below 2 nm for the future technological nodes of the semiconductor roadmap. LER control at the nanometer scale requires accurate measurements. We introduce a technique for LER measurement based upon the atomic force microscope (AFM). In this technique, the sample is tilted at about 45° and feature sidewalls are scanned along their length with the AFM tip to obtain three-dimensional images. The small radius of curvature of the tip together with the low noise level of a laboratory AFM result in high resolution images. Half profiles and LER values on all the height of the sidewalls are extracted from the 3D images using a procedure that we developed. The influence of sample angle variations on the measurements is shown to be small. The technique is applied to the study of a full pattern transfer into a simplified gate stack. The im...

[1]  M. Hussain,et al.  Atomic force microscope study of three-dimensional nanostructure sidewalls , 2007 .

[2]  Olivier Joubert,et al.  Unbiased line width roughness measurements with critical dimension scanning electron microscopy and critical dimension atomic force microscopy , 2012 .

[3]  J. Castle,et al.  Characterization of surface topography by SEM and SFM: problems and solutions , 1997 .

[4]  Ndubuisi G. Orji,et al.  Line edge roughness metrology using atomic force microscopes , 2005 .

[5]  Robert L. Bruce,et al.  On the absence of post-plasma etch surface and line edge roughness in vinylpyridine resists , 2011 .

[6]  G. Cunge,et al.  Surface roughness generated by plasma etching processes of silicon , 2008 .

[7]  H. Sawin,et al.  Review of profile and roughening simulation in microelectronics plasma etching , 2009 .

[9]  T. Chevolleau,et al.  Mass spectrometry studies of resist trimming processes in HBr∕O2 and Cl2∕O2 chemistries , 2005 .

[10]  傾斜 AFM による側壁形状計測の可能性 , 2007 .

[11]  E. Gogolides,et al.  Effects of resist sidewall morphology on line-edge roughness reduction and transfer during etching: is the resist sidewall after development isotropic or anisotropic? , 2010 .

[12]  David B. Graves,et al.  Effects of vacuum ultraviolet photons, ion energy and substrate temperature on line width roughness and RMS surface roughness of patterned 193 nm photoresist , 2011 .

[13]  James W. Taylor,et al.  Correlation of atomic force microscopy sidewall roughness measurements with scanning electron microscopy line-edge roughness measurements on chemically amplified resists exposed by x-ray lithography , 1999 .

[14]  David B. Graves,et al.  Relationship between nanoscale roughness and ion-damaged layer in argon plasma exposed polystyrene films , 2010 .

[15]  Gregg M. Gallatin,et al.  Effect of thin-film imaging on line edge roughness transfer to underlayers during etch processes , 2004 .

[16]  Olivier Joubert,et al.  Linewidth roughness transfer measured by critical dimension atomic force microscopy during plasma patterning of polysilicon gate transistors , 2008 .

[17]  J. Gómez‐Herrero,et al.  WSXM: a software for scanning probe microscopy and a tool for nanotechnology. , 2007, The Review of scientific instruments.

[18]  T. Linton,et al.  Determination of the line edge roughness specification for 34 nm devices , 2002, Digest. International Electron Devices Meeting,.

[19]  David B. Graves,et al.  Understanding the Roughening and Degradation of 193 nm Photoresist during Plasma Processing: Synergistic Roles of Vacuum Ultraviolet Radiation and Ion Bombardment , 2009 .

[20]  Olivier Joubert,et al.  Benefits of plasma treatments on critical dimension control and line width roughness transfer during gate patterning , 2013 .

[21]  Yueming Hua,et al.  Three-dimensional imaging of undercut and sidewall structures by atomic force microscopy. , 2011, The Review of scientific instruments.

[22]  A. Bazin,et al.  Mechanisms involved in HBr and Ar cure plasma treatments applied to 193 nm photoresists , 2009 .

[23]  Olivier Joubert,et al.  Revisiting the mechanisms involved in Line Width Roughness smoothing of 193 nm photoresist patterns during HBr plasma treatment , 2013 .

[24]  Susan C. Palmateer,et al.  Metrology methods for the quantification of edge roughness , 1998, Advanced Lithography.