Numerical investigation on plastic forming for heat transfer tube consisting of both dimples and protrusions

[1]  S. Xie,et al.  A numerical study on heat transfer enhancement and flow structure in enhanced tube with cross ellipsoidal dimples , 2018, International Journal of Heat and Mass Transfer.

[2]  Jie Zhang,et al.  Mechanical response analysis of the buried pipeline due to adjacent foundation pit excavation , 2018, Tunnelling and Underground Space Technology.

[3]  S. Xie,et al.  Numerical investigation on heat transfer performance and flow characteristics in enhanced tube with dimples and protrusions , 2018, International Journal of Heat and Mass Transfer.

[4]  Junghui Chen,et al.  Local flow boiling heat transfer characteristics in three-dimensional enhanced tubes , 2018, International Journal of Heat and Mass Transfer.

[5]  M. Manjunath,et al.  Numerical investigation on heat transfer enhancement of solar air heater using sinusoidal corrugations on absorber plate , 2018 .

[6]  Jie Zhang,et al.  Buckling failure of a buried pipeline subjected to ground explosions , 2018 .

[7]  Ravi Kumar,et al.  Condensation of R-134a inside dimpled helically coiled tube-in-shell type heat exchanger , 2018 .

[8]  S. Nada,et al.  Thermal performance modeling of turbulent flow in multi tube in tube helically coiled heat exchangers , 2018 .

[9]  Yanshan Yin,et al.  Influence of geometric parameters on the thermal hydraulic performance of an ellipsoidal protruded enhanced tube , 2017 .

[10]  S. Wongwises,et al.  Experimental study on two-phase condensation heat transfer and pressure drop of R-134a flowing in a dimpled tube , 2017 .

[11]  Maziar Shafaee,et al.  Evaporation heat transfer and pressure drop characteristics of R-600a in horizontal smooth and helically dimpled tubes , 2016, Applied Thermal Engineering.

[12]  Wei Li,et al.  Comparison of condensation and evaporation heat transfer on the outside of smooth and enhanced 1EHT tubes , 2016 .

[13]  Lei Deng,et al.  An incremental die forging process for producing helical tubes , 2016 .

[14]  Z. Ayub,et al.  Geometric optimization for thermal–hydraulic performance of dimpled enhanced tubes for single phase flow , 2016 .

[15]  Naksoo Kim,et al.  Numerical simulations and experiments on fabricating bend pipes by push bending with local induction-heating process , 2015, The International Journal of Advanced Manufacturing Technology.

[16]  Di Zhang,et al.  Thermal performance of dimpled/protruded circular and annular microchannel tube heat sink , 2016 .

[17]  Prashant Kumar,et al.  Experimental investigation of heat transfer enhancement and fluid flow characteristics in a protruded surface heat exchanger tube , 2016 .

[18]  Wei Liu,et al.  A numerical study on heat transfer enhancement and the flow structure in a heat exchanger tube with discrete double inclined ribs , 2015 .

[19]  Tanit Tangsri,et al.  3D FEM validation of ultra-small inner spiral ribbed copper tube using the tube sinking method , 2015 .

[20]  Tanit Tangsri,et al.  Influences of total reduction of area on drawing stress and tube dimension in inner spiral ribbed copper tube sinking , 2015 .

[21]  Kazunari Yoshida,et al.  Fabrication of small size inner spiral ribbed copper tube by fluid mandrel drawing , 2014 .

[22]  S. Chang,et al.  Heat transfer and pressure drop in hexagonal ducts with surface dimples , 2010 .

[23]  Yong Li,et al.  Forming characteristics analysis of the cross-section of axially inner grooved copper tube , 2010 .

[24]  Yu Wang,et al.  Heat Transfer and Friction Characteristics for Turbulent Flow of Dimpled Tubes , 2009 .

[25]  Beom-Soo Kang,et al.  A prediction of bursting failure in tube hydroforming process based on plastic instability , 2006 .