A method for the on-site determination of prestressing forces using long-gauge fiber optic strain sensors

Structural health monitoring (SHM) consists of the continuous or periodic measurement of structural parameters and their analysis with the aim of deducing information about the performance and health condition of a structure. The significant increase in the construction of prestressed concrete bridges motivated this research on an SHM method for the on-site determination of the distribution of prestressing forces along prestressed concrete beam structures. The estimation of the distribution of forces is important as it can give information regarding the overall performance and structural integrity of the bridge. An inadequate transfer of the designed prestressing forces to the concrete cross-section can lead to a reduced capacity of the bridge and consequently malfunction or failure at lower loads than predicted by design. This paper researches a universal method for the determination of the distribution of prestressing forces along concrete beam structures at the time of transfer of the prestressing force (e.g., at the time of prestressing or post-tensioning). The method is based on the use of long-gauge fiber optic sensors, and the sensor network is similar (practically identical) to the one used for damage identification. The method encompasses the determination of prestressing forces at both healthy and cracked cross-sections, and for the latter it can yield information about the condition of the cracks. The method is validated on-site by comparison to design forces through the application to two structures: (1) a deck-stiffened arch and (2) a curved continuous girder. The uncertainty in the determination of prestressing forces was calculated and the comparison with the design forces has shown very good agreement in most of the structures? cross-sections, but also helped identify some unusual behaviors. The method and its validation are presented in this paper.

[1]  H. Heininger,et al.  Observation of prestress loss in post-tensioned concrete with FBG and LVDT sensors , 2012, 2012 IEEE Conference on Prognostics and Health Management.

[2]  Andrea Del Grosso,et al.  A long-term static monitoring experiment on R.C. beams: damage identification under environmental effect , 2014 .

[3]  M. Chandoga,et al.  Health Monitoring of the Steel Cables Using the Elasto-Magnetic Method , 2002 .

[4]  Jinping Ou,et al.  Monitoring of structural prestress loss in RC beams by inner distributed Brillouin and fiber Bragg grating sensors on a single optical fiber , 2014 .

[5]  R. Tatam,et al.  Optical gas sensing: a review , 2012 .

[6]  Michael Forde,et al.  Ultrasonic tomography of grouted duct post-tensioned reinforced concrete bridge beams , 2001 .

[7]  Craig M. Newtson,et al.  In-Place Modulus of Elasticity for High-Performance Concrete Bridge , 2005 .

[8]  Julie Ditchfield.  Monitoring Temperature Effects on Streicker Bridge Using Fiber Optic Sensors , 2013 .

[9]  Branko Glisic,et al.  Fibre Optic Methods for Structural Health Monitoring , 2007 .

[10]  P. Ziehl,et al.  Acoustic-Emission-Based Characterization of Corrosion Damage in Cracked Concrete with Prestressing Strand , 2013 .

[11]  A W Beeby,et al.  CONCISE EUROCODE FOR THE DESIGN OF CONCRETE BUILDINGS. BASED ON BSI PUBLICATION DD ENV 1992-1-1: 1992. EUROCODE 2: DESIGN OF CONCRETE STRUCTURES. PART 1: GENERAL RULES AND RULES FOR BUILDINGS , 1993 .

[12]  Mary Sansalone,et al.  DETECTING VOIDS IN GROUTED TENDON DUCTS OF POST-TENSIONED CONCRETE STRUCTURES USING THE IMPACT-ECHO METHOD , 1996 .

[13]  Pao Tai Lin,et al.  Mid-infrared materials and devices on a Si platform for optical sensing , 2014, Science and technology of advanced materials.

[14]  Aci Committe.  State-of-the-Art Report on High Strength Concrete , 1984 .

[15]  Claudio Nucera,et al.  Monitoring load levels in multi-wire strands by nonlinear ultrasonic waves , 2011 .

[16]  Carol K. Shield,et al.  Full-scale testing of prestressed concrete bridge girders , 1997 .

[17]  Wei Zhang,et al.  Monitoring the stress of the post-tensioning cable using fiber optic distributed strain sensor , 2006 .

[18]  Branko Glisic,et al.  Detection and Characterization of Early-Age Thermal Cracks in High-Performance Concrete , 2013 .

[19]  Branko Glisic,et al.  Neutral axis as damage sensitive feature , 2013 .

[20]  Daniele Zonta,et al.  Vibration-Based Condition Monitoring of Smart Prefabricated Concrete Elements , 2005 .

[21]  B. Glisic,et al.  Influence of the gauge length on the accuracy of long-gauge sensors employed in monitoring of prismatic beams , 2011 .

[22]  Basile G. Rabbat,et al.  Notes on ACI 318-08, building code requirements for structural concrete : with design applications , 2008 .

[23]  Branko Glisic,et al.  Fibre Optic Methods for Structural Health Monitoring: Glišić/Fibre Optic Methods for Structural Health Monitoring , 2007 .

[24]  B. Glisic.  Streicker bridge: A two-year monitoring overview , 2012 .