Rapeseed impact against a flat surface: Physical testing and DEM simulation with two contact models

Abstract Efficient application of a discrete element method (DEM) in modeling the behavior of granular materials requires contact models that reflect real behavior and realistic material parameters. The mechanical behavior of materials of biological origin is strongly influenced by the moisture content, which changes the surface and mechanical properties of seed endosperm and influences the bulk behavior. Laboratory tests and numerical DEM simulations were conducted to evaluate regions of validity for two basic contact models to describe the impact behavior of rapeseed at four moisture contents (5.5%, 7.5%, 14.7% and 34.0%). Seeds were allowed to free fall onto a flat surface from a height of 21 cm. Force–time waveforms were recorded using oscilloscope and rise and fall times were extracted for further analysis. DEM simulations were performed in which material parameters determined by a standard method fitted to two contact models were compared to experimental contact time measurements. The elastoplastic model was suitable for impact of dry seeds, whereas the viscoelastic model gave a better fit for wet seeds. An efficient criterion for model selection was the ratio of the fall time to the rise time (TR) for the contact force–time characteristic. For TR   1 the viscoplastic model should be applied.

[1]  Christine M. Hrenya,et al.  Comparison of soft-sphere models to measurements of collision properties during normal impacts , 2005 .

[2]  C. Thornton,et al.  Impact behaviour of elastoplastic spheres with a rigid wall , 2000 .

[3]  L. Vu-Quoc,et al.  An elastoplastic contact force–displacement model in the normal direction: displacement–driven version , 1999, Proceedings of the Royal Society of London. Series A: Mathematical, Physical and Engineering Sciences.

[4]  C. Thornton,et al.  A theoretical model for the stick/bounce behaviour of adhesive, elastic-plastic spheres , 1998 .

[5]  A. Pineau.  Modeling ductile to brittle fracture transition in steels—micromechanical and physical challenges , 2008 .

[6]  G. Szwed,et al.  Effect of rapeseed and wheat kernel moisture on impact damage , 2007 .

[7]  Herman Ramon,et al.  Determination of the dynamical behaviour of biological materials during impact using a pendulum device , 2003 .

[8]  G. Weir,et al.  The coefficient of restitution for normal incident, low velocity particle impacts , 2005 .

[9]  Harald Kruggel-Emden,et al.  Review and extension of normal force models for the Discrete Element Method , 2007 .

[10]  M. Molenda,et al.  Determination of the elastic constants of cereal grains in a uniaxial compression test , 2002 .

[11]  M. Thompson,et al.  Determining the collision properties of semi-crystalline and amorphous thermoplastics for DEM simulations of solids transport in an extruder , 2007 .

[12]  Michel Y. Louge,et al.  Measurements of the collision properties of small spheres , 1994 .

[13]  W. J. Whiten,et al.  The calculation of contact forces between particles using spring and damping models , 1996 .

[14]  Norman A. Fleck,et al.  Frictionless indentation of dissimilar elastic-plastic spheres , 2000 .

[15]  H. Ramon,et al.  On the accuracy of the Hertz model to describe the normal contact of soft elastic spheres , 2008 .

[16]  M. J. Pitts,et al.  Fundamental physical properties characterizing the hardness of wheat endosperm , 1991 .

[17]  Y. Tsuji,et al.  Discrete particle simulation of two-dimensional fluidized bed , 1993 .

[18]  Mohammad Hossein Abbaspour-Fard,et al.  Theoretical Validation of a Multi-sphere, Discrete Element Model Suitable for Biomaterials Handling Simulation , 2004 .

[19]  T. Winnicki,et al.  Effect of drying of rapeseeds on their mechanical properties and technological usability , 1994 .

[20]  I. Etsion,et al.  UNLOADING OF AN ELASTIC-PLASTIC LOADED SPHERICAL CONTACT , 2005 .

[21]  C. Thornton,et al.  Rebound behaviour of spheres for plastic impacts , 2003 .

[22]  Colin Thornton,et al.  A theoretical model for the contact of elastoplastic bodies , 2001 .

[23]  H. Ramon,et al.  The discrete element method (DEM) to simulate fruit impact damage during transport and handling: Case study of vibration damage during apple bulk transport , 2006 .

[24]  J. Favier,et al.  Model for the deformation in agricultural and food particulate materials under bulk compressive loading using discrete element method. I: Theory, model development and validation , 2004 .

[25]  E. Davison.  A THEORETICALSTRESS MODEL OF RAPESEED , 1979 .

[26]  K. Supulver,et al.  The Coefficient of Restitution of Ice Particles in Glancing Collisions: Experimental Results for Unfrosted Surfaces , 1995 .

[27]  G. Kuwabara,et al.  Restitution Coefficient in a Collision between Two Spheres , 1987 .

[28]  S. Timoshenko,et al.  Theory of elasticity , 1975 .