A nonlinear sliding mode observer for the estimation of temperature distribution in a planar solid oxide fuel cell

Abstract Compliance to certain temperature constraints is essential for the long life and stable operation of solid oxide fuel cells (SOFCs). However, it is difficult and costly to measure the temperature inside a high temperature, well-sealed cell directly. A nonlinear sliding mode observer has been designed in this paper for estimating the temperature distribution in a hydrogen fed SOFC stack. The observer design is based on a finite-volume parameter SOFC model, which is simplified by quasi-static mass balance assumption. In the observer design, a decoupling pole placement method that applies to multi-timescale systems is proposed to obtain a suitable observer gain. And a quasi-sliding mode control method is adopted to eliminate the chatter caused by the discontinuous control actions of sliding mode control. Theoretical analysis and simulation results are presented to prove the convergence and good performance of the designed observer for estimating the temperature distribution in a SOFC stack during steady-state and transient operation.

[1]  Lieh-Kwang Chiang,et al.  Thermal stress analysis of a planar SOFC stack , 2007 .

[2]  J. Barbot,et al.  A finite time observer for flux estimation in the induction machine , 2002, Proceedings of the International Conference on Control Applications.

[3]  K. Kendall,et al.  High temperature solid oxide fuel cells : fundamentals, design and applicatons , 2003 .

[4]  C. W. Hong,et al.  Cold start dynamics and temperature sliding observer design of an automotive SOFC APU , 2009 .

[5]  A. Selçuk,et al.  The influence of electrodes on the strength of planar zirconia solid oxide fuel cells , 2001 .

[6]  T. Floquet,et al.  On Sliding Mode Observers for Systems with Unknown Inputs , 2006, International Workshop on Variable Structure Systems, 2006. VSS'06..

[7]  Carlos Canudas de Wit,et al.  Sliding observers for robot manipulators , 1991, Autom..

[8]  Jie Yang,et al.  Parameter optimization for tubular solid oxide fuel cell stack based on the dynamic model and an imp , 2011 .

[9]  Christopher Edwards,et al.  Sensor fault tolerant control using sliding mode observers , 2006 .

[10]  Xi Li,et al.  Generalized predictive control for fractional order dynamic model of solid oxide fuel cell output power , 2010 .

[11]  Vicenç Puig,et al.  LPV observer design for PEM fuel cell system: Application to fault detection , 2011 .

[12]  Jing Sun,et al.  Estimation of Spatial Temperature Distribution in Co-Flow Planar Solid Oxide Fuel Cells , 2007 .

[13]  James Larminie,et al.  Fuel Cell Systems Explained , 2000 .

[14]  Moses O. Tadé,et al.  Effect of the Operating Strategy of a Solid Oxide Fuel Cell on the Effectiveness of Decentralized Linear Controllers , 2011 .

[15]  Moses O. Tadé,et al.  An adaptive non-linear observer for the estimation of temperature distribution in the planar solid oxide fuel cell , 2013 .

[16]  T. Floquet *,et al.  On the robust fault detection via a sliding mode disturbance observer , 2004 .

[17]  Vadim I. Utkin,et al.  Sliding Modes in Control and Optimization , 1992, Communications and Control Engineering Series.

[18]  Shinji Kimijima,et al.  The effect of overpotentials on the transient response of the 300W SOFC cell stack voltage , 2014 .

[19]  Handa Xi.  Dynamic modeling and control of planar SOFC power systems. , 2007 .

[20]  Vadim I. Utkin,et al.  Sliding mode control design principles and applications to electric drives , 1993, IEEE Trans. Ind. Electron..

[21]  Hongliang Cao,et al.  Dynamic modeling and experimental validation for the electrical coupling in a 5-cell solid oxide fuel cell stack in the perspective of thermal coupling , 2011 .

[22]  Raphaël Ihringer,et al.  Dynamic behaviour of SOFC short stacks , 2006 .

[23]  Jean-Pierre Barbot,et al.  Sliding observer-based feedback control for flexible joints manipulator , 1996, Autom..