Ultrafine grains and the Hall-Petch relationship in an Al-Mg-Si alloy processed by high-pressure torsion

Abstract Experiments were conducted to evaluate the evolution of hardness and microstructure in a commercial Al–0.6% Mg–0.4% Si alloy during processing by high-pressure torsion (HPT). The HPT was conducted under a pressure of 6.0 GPa and disks were torsionally strained to a maximum of 20 turns. It is shown that processing by HPT leads to microstructural refinement with an average grain size of ∼250 nm and to an increase in hardness up to a saturation value at equivalent strains above ∼100. There is a deviation in the Hall–Petch relationship at grain sizes smaller than ∼500 nm and this is consistent with an earlier suggestion that a breakdown may occur if there is an easy movement of the extrinsic dislocations in the non-equilibrium grain boundaries introduced by HPT processing.

[1]  R. Valiev,et al.  Nanostructure and related mechanical properties of an Al–Mg–Si alloy processed by severe plastic deformation , 2008, 0808.3715.

[2]  Y. Estrin,et al.  Strain gradient plasticity modelling of high-pressure torsion , 2008 .

[3]  T. Langdon,et al.  Effect of strain reversals on the processing of high-purity aluminum by high-pressure torsion , 2010 .

[4]  K. Edalati,et al.  Continuous high-pressure torsion , 2010 .

[5]  N. Gao,et al.  Influence of strain rate on the characteristics of a magnesium alloy processed by high-pressure torsion , 2011 .

[6]  K. Edalati,et al.  The significance of slippage in processing by high-pressure torsion , 2009 .

[7]  T. Langdon,et al.  The significance of strain reversals during processing by high-pressure torsion , 2008 .

[8]  T. Langdon,et al.  Three-dimensional representations of hardness distributions after processing by high-pressure torsion , 2009 .

[9]  R. Valiev,et al.  Structure and deformaton behaviour of Armco iron subjected to severe plastic deformation , 1996 .

[10]  Terence G. Langdon,et al.  Using high-pressure torsion for metal processing: Fundamentals and applications , 2008 .

[11]  R. Valiev,et al.  The Hall-Petch relation in submicro-grained Al-1.5% Mg alloy , 1992 .

[12]  R. Valiev,et al.  Principles of equal-channel angular pressing as a processing tool for grain refinement , 2006 .

[13]  H. Kanayama,et al.  Significance of temperature increase in processing by high-pressure torsion , 2011 .

[14]  Reinhard Pippan,et al.  Saturation of Fragmentation During Severe Plastic Deformation , 2010 .

[15]  Maria Dolors Baró,et al.  Experimental parameters influencing grain refinement and microstructural evolution during high-pressure torsion , 2003 .

[16]  R. Valiev,et al.  Microhardness and microstructural evolution in pure nickel during high-pressure torsion , 2001 .

[17]  R. Valiev,et al.  Structural evolution and the Hall-Petch relationship in an Al-Mg-Li-Zr alloy with ultra-fine grain size , 1997 .

[18]  Sun Ig Hong,et al.  Plastic deformation analysis of metals during equal channel angular pressing , 2001 .

[19]  B. Gludovatz,et al.  Technical parameters affecting grain refinement by high pressure torsion , 2009 .

[20]  R. Valiev,et al.  Factors influencing the flow and hardness of materials with ultrafine grain sizes , 1998 .

[21]  J. Mackenzie,et al.  SECOND PAPER ON STATISTICS ASSOCIATED WITH THE RANDOM DISORIENTATION OF CUBES , 1958 .

[22]  T. Langdon,et al.  The evolution of homogeneity in processing by high-pressure torsion , 2007 .

[23]  J. Mackenzie,et al.  SOME STATISTICS ASSOCIATED WITH THE RANDOM DISORIENTATION OF CUBES , 1957 .

[24]  R. Srinivasan,et al.  Scaling up of equal-channel angular pressing and its effect on mechanical properties, microstructure, and hot workability of AA 6061 , 2005 .

[25]  M. Meyers,et al.  Mechanical properties of nanocrystalline materials , 2006 .

[26]  T. Langdon,et al.  Using finite element modeling to examine the flow processes in quasi-constrained high-pressure torsion , 2011 .

[27]  T. Langdon,et al.  Microstructural evolution in commercial purity aluminum during high-pressure torsion , 2005 .

[28]  T. Langdon,et al.  Evaluating the influence of pressure and torsional strain on processing by high-pressure torsion , 2008, Journal of Materials Science.

[29]  R. Pippan,et al.  TEM investigations of the structural evolution in a pearlitic steel deformed by high-pressure torsion , 2006 .

[30]  T. Baudin,et al.  Microstructural evolution in an Al-6061 alloy processed by high-pressure torsion , 2010 .

[31]  K. Lu,et al.  Enhancement of strength and stability of nanostructured Ni by small amounts of solutes , 2011 .

[32]  T. Langdon,et al.  The potential for scaling ECAP: effect of sample size on grain refinement and mechanical properties , 2001 .

[33]  T. Langdon,et al.  The evolution of homogeneity in an aluminum alloy processed using high-pressure torsion , 2008 .

[34]  T. Langdon,et al.  Developing high-pressure torsion for use with bulk samples , 2005 .

[35]  E. Hall,et al.  The Deformation and Ageing of Mild Steel: III Discussion of Results , 1951 .

[36]  T. Langdon,et al.  Orientation imaging microscopy of ultrafine-grained nickel , 2002 .

[37]  R. Valiev,et al.  Processing of nanostructured metals and alloys via plastic deformation , 2010 .

[38]  Yuri Estrin,et al.  Producing bulk ultrafine-grained materials by severe plastic deformation , 2006 .

[39]  R. Pippan,et al.  On the homogeneity of deformation by high pressure torsion , 2004 .

[40]  R. Valiev,et al.  Microhardness measurements and the Hall-Petch relationship in an AlMg alloy with submicrometer grain size , 1996 .

[41]  T. Baudin,et al.  Microstructural and textural characterization of copper processed by ECAE , 2006 .

[42]  X. Liao,et al.  Influence of high-pressure torsion on microstructural evolution in an Al–Zn–Mg–Cu alloy , 2010 .

[43]  R. Valiev,et al.  Bulk nanostructured materials from severe plastic deformation , 2000 .

[44]  T. Langdon,et al.  Microstructural evolution in a two-phase alloy processed by high-pressure torsion , 2010 .

[45]  The microstructural characteristics of ultrafine-grained nickel , 2005 .

[46]  R. Pippan,et al.  The Limits of Refinement by Severe Plastic Deformation , 2006 .