Design and optimization of a combined fuel reforming and solid oxide fuel cell system with anode off-gas recycling

Abstract An energy conversion and management concept for a combined system of a solid oxide fuel cell coupled with a fuel reforming device is developed and analyzed by a thermodynamic and electrochemical model. The model is verified by an experiment and then used to evaluate the overall system performance and to further suggest an optimal design strategy. The unique feature of the system is the inclusion of the anode off-gas recycle that eliminates the need of external water consumption for practical applications. The system performance is evaluated as a function of the steam to carbon ratio, fuel cell temperature, anode off gas recycle ratio and CO 2 adsorption percentage. For most of the operating conditions investigated, the system efficiency starts at around 70% and then monotonically decreases to the average of 50% at the peak power density before dropping down to zero at the limiting current density point. From an engineering application point of view, the proposed combined fuel reforming and SOFC system with a range of efficiency between 50% and 70% is considered very attractive. It is suggested that the optimal system is the one where the SOFC operates around 900 °C with S / C ratio higher than 3, maximum CO 2 capture, and minimum AOG recirculation.

[1]  David J. Bayless,et al.  Analysis of jet fuel reforming for solid oxide fuel cell applications in auxiliary power units , 2008 .

[2]  Kazunari Sasaki,et al.  Multi-Fuel Capability of Solid Oxide Fuel Cells , 2004 .

[3]  N. Bessette,et al.  A Mathematical Model of a Solid Oxide Fuel Cell , 1995 .

[4]  I. Dincer,et al.  Thermodynamic modeling of direct internal reforming solid oxide fuel cells operating with syngas , 2007 .

[5]  K. Sasaki,et al.  Equilibria in Fuel Cell Gases I. Equilibrium Compositions and Reforming Conditions , 2003 .

[6]  Donald J. Chmielewski,et al.  Autothermal Reforming of Gasoline for Fuel Cell Applications: A Transient Reactor Model , 2006 .

[7]  S. Chan,et al.  Energy and exergy analysis of simple solid-oxide fuel-cell power systems , 2002 .

[8]  F. R. Foulkes,et al.  Fuel Cell Handbook , 1989 .

[9]  S. Singhal,et al.  Polarization Effects in Intermediate Temperature, Anode‐Supported Solid Oxide Fuel Cells , 1999 .

[10]  J. Smith,et al.  Introduction to chemical engineering thermodynamics , 1949 .

[11]  P. Ekdunge,et al.  Diesel fuel reformer for automotive fuel cell applications , 2009 .

[12]  A. London,et al.  Compact heat exchangers , 1960 .

[13]  David A. Berry,et al.  Effects of fuel cell anode recycle on catalytic fuel reforming , 2007 .

[14]  B. Höhlein,et al.  Compact methanol reformer test for fuel-cell powered light-duty vehicles , 1998 .

[15]  Jens R. Rostrup-Nielsen.  Conversion of hydrocarbons and alcohols for fuel cells , 2001 .

[16]  Sangho Yoon,et al.  The operating characteristics of solid oxide fuel cells driven by diesel autothermal reformate , 2008 .

[17]  T. Kaun,et al.  Characterization of kilowatt-scale autothermal reformer for production of hydrogen from heavy hydrocarbons , 2004 .

[18]  M. Krumpelt,et al.  Hydrogen from hydrocarbon fuels for fuel cells , 2001 .

[19]  Daniela Chrenko,et al.  Static and dynamic modeling of a diesel fuel processing unit for polymer electrolyte fuel cell supply , 2009 .

[20]  Yulong Ding,et al.  Adsorption-enhanced steam–methane reforming , 2000 .

[21]  Kazunari Sasaki,et al.  Equilibria in Fuel Cell Gases II. The C-H-O Ternary Diagrams , 2003 .

[22]  Vito Specchia,et al.  Diesel fuel processor for PEM fuel cells: Two possible alternatives (ATR versus SR) , 2006 .

[23]  I. Dincer,et al.  A review on macro‐level modeling of planar solid oxide fuel cells , 2008 .