Forming limit investigation of friction stir welded sheets: influence of shoulder diameter and plunge depth

The main aim of the present work is to analyze the influence of shoulder diameter and plunge depth on the formability of friction stir welded sheets. The base material used for welding and forming was AA6061-T6. Formability evaluation was performed through limiting dome height tests. The forming limit curve, FLC (only in the stretching region), thickness distribution, and strain hardening exponent of the weld region were monitored during formability studies. It is found from the work that the forming limit of friction stir welded sheets is better than unwelded sheets. In general, with an increase in shoulder diameter and plunge depth, the forming limit is found to improve considerably. With a decrease in thickness gradient severity and an increase in strain hardening exponent (n) of the weld region, the forming limit is found to increase. The increase in n value of the weld region is believed to occur because of the reduction in dislocation density. The maximum thickness difference is higher in the retreating side, rather than in the advancing side, of the weld. This is due to the differential straining and hardness levels attained by both sides during friction stir welding.

[1]  L. D. Filippis,et al.  Effect of shoulder geometry on residual stress and fatigue properties of AA6082 fsw joints , 2009 .

[2]  Z. Ma,et al.  Influence of Tool Dimension and Welding Parameters on Microstructure and Mechanical Properties of Friction-Stir-Welded 6061-T651 Aluminum Alloy , 2008 .

[3]  H. Bhadeshia,et al.  Recent advances in friction-stir welding : Process, weldment structure and properties , 2008 .

[4]  V. Balasubramanian,et al.  Influences of tool pin profile and axial force on the formation of friction stir processing zone in AA6061 aluminium alloy , 2008 .

[5]  Michael Miles,et al.  Formability and strength of friction-stir-welded aluminum sheets , 2004 .

[6]  X. S. Wang,et al.  Formability and microstructural stability of friction stir welded Al alloy tube during subsequent spinning and post weld heat treatment , 2012 .

[7]  K. Oh,et al.  Relationship between formability and microstructure of Al alloy sheet locally modified by friction stir processing , 2007 .

[8]  Levente Balogh,et al.  Grain structure and dislocation density measurements in a friction-stir welded aluminum alloy using X-ray peak profile analysis , 2008 .

[9]  P. Threadgill,et al.  Friction stir welding of aluminium alloys , 2009 .

[10]  Kwansoo Chung,et al.  Experimental and numerical study on formability of friction stir welded TWB sheets based on hemispherical dome stretch tests , 2009 .

[11]  Birgit Skrotzki,et al.  Characterization of a friction-stir-welded aluminum alloy 6013 , 2002 .

[12]  M. W. Mahoney,et al.  Properties of friction-stir-welded 7075 T651 aluminum , 1998 .

[13]  H. Fujii,et al.  Tensile properties and fracture locations of friction-stir welded joints of 6061-T6 aluminum alloy , 2003 .

[14]  Radovan Kovacevic,et al.  Thermal modeling of friction stir welding in a moving coordinate system and its validation , 2003 .

[15]  G. Goerigk,et al.  Dependence of the microstructure, residual stresses and texture of AA 6013 friction stir welds on the welding proces , 2003, International Journal of Materials Research - Zeitschrift für Metallkunde.

[16]  Satish V. Kailas,et al.  The role of friction stir welding tool on material flow and weld formation , 2008 .

[17]  A. Forcellese,et al.  Post-welding formability of AZ31 magnesium alloy , 2011 .

[18]  H. Kokawa,et al.  Distribution of tensile property and microstructure in friction stir weld of 6063 aluminum , 2001 .

[19]  Sung Wook Chung,et al.  Influence of friction stir welding parameters on grain size and formability in 5083 aluminum alloy , 2007 .

[20]  A. Scialpi,et al.  Influence of shoulder geometry on microstructure and mechanical properties of friction stir welded 6082 aluminium alloy , 2007 .

[21]  Hiroyuki Kokawa,et al.  Post-weld formability of friction stir welded Al alloy 5052 , 2004 .

[22]  Dulce Maria Rodrigues,et al.  Formability of similar and dissimilar friction stir welded AA 5182-H111 and AA 6016-T4 tailored blanks , 2009 .

[23]  Rajiv S. Mishra,et al.  Friction Stir Welding and Processing , 2007 .

[24]  Michael Miles,et al.  Formability of friction-stir-welded dissimilar-aluminum-alloy sheets , 2005 .

[25]  Kwansoo Chung,et al.  Macro-performance evaluation of friction stir welded automotive tailor-welded blank sheets: Part I - Material properties , 2010 .

[26]  K. Chung,et al.  Formability evaluation of friction stir welded 6111-T4 sheet with respect to joining material direction , 2010 .

[27]  Ji Hoon Kim,et al.  Themo-mechanical and microstructural modeling of friction stir welding of 6111-T4 aluminum alloys , 2009 .

[28]  Thomas Pardoen,et al.  Microstructure, local and global mechanical properties of friction stir welds in aluminium alloy 6005A-T6 , 2008 .

[29]  Pedro Vilaça,et al.  Material flow in heterogeneous friction stir welding of thin aluminium sheets: Effect of shoulder geometry , 2008 .

[30]  V. Balasubramanian,et al.  Influences of tool pin profile and tool shoulder diameter on the formation of friction stir processing zone in AA6061 aluminium alloy , 2008 .

[31]  Hidetoshi Fujii,et al.  Effect of tool shape on mechanical properties and microstructure of friction stir welded aluminum alloys , 2006 .

[32]  Christophe Desrayaud,et al.  Mechanical and thermal modelling of Friction Stir Welding , 2006 .

[33]  G. Çam,et al.  Friction stir welded structural materials: beyond Al-alloys , 2011 .

[34]  C. Muralidharan,et al.  Predicting tensile strength, hardness and corrosion rate of friction stir welded AA6061-T6 aluminium alloy joints , 2011 .

[35]  Kwansoo Chung,et al.  Macro-performance evaluation of friction stir welded automotive tailor-welded blank sheets: Part II – Formability , 2010 .

[36]  A. A. Zadpoor,et al.  Global and Local Mechanical Properties and Microstructure of Friction Stir Welds with Dissimilar Materials and/or Thicknesses , 2010 .