Phase-field simulation of solidification morphology in laser powder deposition of Ti-Nb alloys

Abstract A phase-field model of alloy solidification is coupled to a new heat transfer finite element model of the laser powder deposition process. The robustness and accuracy of the coupled model is validated by studying spacing evolution under the directional solidification conditions in laser powder deposition of Ti–Nb alloys. Experimental Ti–Nb samples reveal the microstructure on a longitudinal section with significant change in the size of the dendrites across the sample. Quantitative phase-field simulations of directional solidification under local steady-state conditions extracted from the results of the finite element thermal model confirmed this behavior. Specifically, the phase-field simulations agree with the results of the analytical model of Hunt in predicting a minimum spacing value, which is due to the mutual effects of the increasing temperature gradient and decreasing solidification velocity towards the bottom of the microstructure. This work demonstrates the potential of coupling the phase-field method to complex heat transfer conditions necessary to simulate topologically complex microstructure morphologies present in laser powder deposition and other industrially relevant casting conditions.

[1]  Mikko Haataja,et al.  Crossover scaling of wavelength selection in directional solidification of binary alloys. , 2004, Physical review letters.

[2]  Nikolas Provatas,et al.  Phase-field study of spacing evolution during transient growth. , 2010, Physical review. E, Statistical, nonlinear, and soft matter physics.

[3]  S. Felicelli,et al.  Dendrite growth simulation during solidification in the LENS process , 2010 .

[4]  A. Khajepour,et al.  Temporal development of melt-pool morphology and clad geometry in laser powder deposition , 2011 .

[5]  Department of Physics,et al.  EFFICIENT COMPUTATION OF DENDRITIC MICROSTRUCTURES USING ADAPTIVE MESH REFINEMENT , 1998 .

[6]  A. Karma,et al.  Quantitative phase-field model of alloy solidification. , 2004, Physical review. E, Statistical, nonlinear, and soft matter physics.

[7]  J. Murray.  The Nb−Ti (Niobium-Titanium) system , 1981 .

[8]  Juan C. Heinrich,et al.  Modeling dendritic growth of a binary alloy , 2003 .

[9]  J. Hunt,et al.  Numerical modeling of cellular/dendritic array growth: spacing and structure predictions , 1996 .

[10]  A. Karma,et al.  Phase-Field Simulation of Solidification , 2002 .

[11]  N. Provatas,et al.  Spacing Characterization in Al-Cu Alloys Directionally Solidified Under Transient Growth Conditions , 2010, 1002.1699.

[12]  M. Rappaz,et al.  A Pseudo-Front Tracking Technique for the Modelling of Solidification Microstructures in Multi-Component Alloys , 2002 .

[13]  D. Stefanescu,et al.  Growth of solutal dendrites—A cellular automaton model , 2003 .

[14]  V. Pavlyk,et al.  Simulation of weld solidification microstructure and its coupling to the macroscopic heat and fluid flow modelling , 2004 .

[15]  W. Kurz,et al.  Fundamentals of Solidification , 1990 .

[16]  Nikolas Provatas,et al.  Phase-Field Methods in Materials Science and Engineering , 2010 .

[17]  M. McLean,et al.  Directionally Solidified Materials for High Temperature Service , 1984 .

[18]  X. Zhan,et al.  Simulation of grain morphologies and competitive growth in weld pool of Ni–Cr alloy , 2009 .

[19]  Y. Shin,et al.  A novel integrated model combining Cellular Automata and Phase Field methods for microstructure evolution during solidification of multi-component and multi-phase alloys , 2011 .

[20]  Amir Khajepour,et al.  Process optimization of Ti–Nb alloy coatings on a Ti–6Al–4V plate using a fiber laser and blended elemental powders , 2010 .

[21]  D. G. McCartney,et al.  A Numerical Finite Difference Model of Steady State Cellular and Dendritic Growth , 1984 .

[22]  J. Warren,et al.  Prediction of dendritic growth and microsegregation patterns in a binary alloy using the phase-field method , 1995 .

[23]  M. Zimmermann,et al.  Rapid solidification of Al-Cu eutectic alloy by laser remelting , 1989 .

[24]  R. Trivedi,et al.  Microstructure and Phase Selection in Laser Treatment of Materials , 1992 .

[25]  Wilfried Kurz,et al.  Dendrite growth at the limit of stability: tip radius and spacing , 1981 .

[26]  Karma,et al.  Numerical Simulation of Three-Dimensional Dendritic Growth. , 1996, Physical review letters.

[27]  R. Sekerka,et al.  Stability of a Planar Interface During Solidification of a Dilute Binary Alloy , 1964 .

[28]  Chih-Jen Shih,et al.  Adaptive phase field simulation of non-isothermal free dendritic growth of a binary alloy , 2003 .

[29]  J. Warren,et al.  Modelling polycrystalline solidification using phase field theory , 2004 .

[30]  Badrinarayan P. Athreya,et al.  Adaptive mesh computation of polycrystalline pattern formation using a renormalization-group reduction of the phase-field crystal model. , 2007, Physical review. E, Statistical, nonlinear, and soft matter physics.

[31]  A. Karma,et al.  Quantitative phase-field modeling of dendritic growth in two and three dimensions , 1996 .

[32]  A. Karma,et al.  Phase-field modeling of binary alloy solidification with coupled heat and solute diffusion. , 2004, Physical review. E, Statistical, nonlinear, and soft matter physics.

[33]  Michael J. Aziz,et al.  Model for solute redistribution during rapid solidification , 1982 .

[34]  Gustav Amberg,et al.  Phase-field simulations of non-isothermal binary alloy solidification , 2001 .

[35]  A. Kokabi,et al.  Phase-field simulation of weld solidification microstructure in an Al–Cu alloy , 2008 .

[36]  K. Mills.  Recommended Values of Thermophysical Properties for Selected Commercial Alloys , 2001 .