Influence of testing and tempering temperatures on fatigue behaviour, life and crack initiation mechanisms in a 5%Cr martensitic steel

[1]  A. Hartmaier,et al.  How dislocation substructures evolve during long-term creep of a 12% Cr tempered martensitic ferritic steel , 2010 .

[2]  B. Fournier,et al.  Analysis of the hysteresis loops of a martensitic steel: Part I: Study of the influence of strain amplitude and temperature under pure fatigue loadings using an enhanced stress partitioning method , 2006 .

[3]  L. Penazzi,et al.  A continuum damage model applied to high temperature fatigue lifetime prediction of a martensitic tool steel , 2005 .

[4]  C. Levaillant,et al.  Relationship between microstructure and mechanical properties of a 5% Cr tempered martensitic tool steel , 2004 .

[5]  G. Bernhart,et al.  Microstructure evolution of hot-work tool steels during tempering and definition of a kinetic law based on hardness measurements , 2004 .

[6]  Gunther Eggeler,et al.  The evolution of dislocation density during heat treatment and creep of tempered martensite ferritic steels , 2003 .

[7]  K. A. Padmanabhan,et al.  Low cycle fatigue behavior of a multiphase microalloyed medium carbon steel: comparison between ferrite–pearlite and quenched and tempered microstructures , 2003 .

[8]  Z. Zhang,et al.  Anisothermal cyclic plasticity modelling of martensitic steels , 2002 .

[9]  S. L. Roux,et al.  Thermomechanical fatigue behaviour and life assessment of hot work tool steels , 2002 .

[10]  J. Gubicza,et al.  Crystallite size distribution and dislocation structure determined by diffraction profile analysis: principles and practical application to cubic and hexagonal crystals , 2001 .

[11]  J. Gubicza,et al.  Particle size distribution and dislocation density determined by high resolution X-ray diffraction in nanocrystalline silicon nitride powders , 2000 .

[12]  P. Sanders,et al.  Dislocations, grain size and planar faults in nanostructured copper determined by high resolution X-ray diffraction and a new procedure of peak profile analysis , 1998 .

[13]  Tamás Ungár,et al.  The effect of dislocation contrast on x‐ray line broadening: A new approach to line profile analysis , 1996 .

[14]  J. Lendvai,et al.  Dislocations and grain size in ball-milled iron powder , 1996 .

[15]  K. Fukaura,et al.  Effect of Testing Atmosphere on Low Cycle Fatigue of Hot Work Tool Steel at Elevated Temperature , 1995 .

[16]  C. Tsai,et al.  Effects of temperature on the cyclic deformation behaviour and microstructural changes of 12Cr-1MoVW martensitic stainless steel , 1994 .

[17]  A. P. Voskamp,et al.  FATIGUE BEHAVIOUR OF THREE VARIANTS OF THE ROLLER BEARING STEEL SAE 52100 , 1992 .

[18]  D. S. Sarma,et al.  Influence of high temperature low cycle fatigue deformation on the microstructure of a CrMoV rotor steel subjected to long-term service exposure at 425°C and retempering at 677°C , 1992 .

[19]  S. Mediratta,et al.  Cyclic work hardening and formation of dislocation substructures during low‐cycle fatigue of tempered dual‐phase steels , 1990 .

[20]  Gunther Eggeler,et al.  The effect of long-term creep on particle coarsening in tempered martensite ferritic steels , 1989 .

[21]  G. Eggeler,et al.  Deformation and damage processes in a 12%CrMoV steel under high temperature low cycle fatigue conditions in air and vacuum , 1989 .

[22]  J. Vogt,et al.  CYCLIC MECHANICAL BEHAVIOR AND MICROSTRUCTURE OF A 12Cr-Mo-V MARTENSITIC STAINLESS STEEL , 1988 .

[23]  C. Laird,et al.  Changes in morphology and composition of carbides during cyclic deformation at room and elevated temperature and their effect on mechanical properties of CrMoV steel , 1985 .

[24]  K. Kanazawa,et al.  The temperature dependence of low cycle fatigue behaviour of martensitic stainless steels , 1979 .