Intelligent process modeling and optimization of die-sinking electric discharge machining

This paper reports an intelligent approach for process modeling and optimization of electric discharge machining (EDM). Physics based process modeling using finite element method (FEM) has been integrated with the soft computing techniques like artificial neural networks (ANN) and genetic algorithm (GA) to improve prediction accuracy of the model with less dependency on the experimental data. A two-dimensional axi-symmetric numerical (FEM) model of single spark EDM process has been developed based on more realistic assumptions such as Gaussian distribution of heat flux, time and energy dependent spark radius, etc. to predict the shape of crater, material removal rate (MRR) and tool wear rate (TWR). The model is validated using the reported analytical and experimental results. A comprehensive ANN based process model is proposed to establish relation between input process conditions (current, discharge voltage, duty cycle and discharge duration) and the process responses (crater size, MRR and TWR) .The ANN model was trained, tested and tuned by using the data generated from the numerical (FEM) model. It was found to accurately predict EDM process responses for chosen process conditions. The developed ANN process model was used in conjunction with the evolutionary non-dominated sorting genetic algorithm II (NSGA-II) to select optimal process parameters for roughing and finishing operations of EDM. Experimental studies were carried out to verify the process performance for the optimum machining conditions suggested by our approach. The proposed integrated (FEM-ANN-GA) approach was found efficient and robust as the suggested optimum process parameters were found to give the expected optimum performance of the EDM process.

[1]  Martin Fodslette Møller,et al.  A scaled conjugate gradient algorithm for fast supervised learning , 1993, Neural Networks.

[2]  Pei-Jen Wang,et al.  Comparisons of neural network models on material removal rate in electrical discharge machining , 2001 .

[3]  Rajat Kumar Bhoi,et al.  Developing Transient Three Dimensional Thermal Models for Electro Discharge Machining of Semi Infinite and Infinite Solid , 2001 .

[4]  Lyndon Smith,et al.  A neural network approach for solution of the inverse problem for selection of powder metallurgy materials , 2002 .

[5]  Surjya K. Pal,et al.  Modeling of electrical discharge machining process using back propagation neural network and multi-objective optimization using non-dominating sorting genetic algorithm-II , 2007 .

[6]  Jesús Manuel Fernández Salido,et al.  A comparison of two learning mechanisms for the automatic design of fuzzy diagnosis systems for rotating machinery , 2004, Appl. Soft Comput..

[7]  Kalyanmoy Deb,et al.  Muiltiobjective Optimization Using Nondominated Sorting in Genetic Algorithms , 1994, Evolutionary Computation.

[8]  Xiaolin Chen,et al.  Process simulation of micro electro-discharge machining on molybdenum , 2007 .

[9]  H. S. Shan,et al.  Electro jet drilling using hybrid NNGA approach , 2007 .

[10]  F. Amorim,et al.  The influence of generator actuation mode and process parameters on the performance of finish EDM of a tool steel , 2005 .

[11]  Fu-Chen Chen,et al.  Multi-objective optimisation of high-speed electrical discharge machining process using a Taguchi fuzzy-based approach , 2007 .

[12]  Angelos P. Markopoulos,et al.  Artificial neural network models for the prediction of surface roughness in electrical discharge machining , 2008, J. Intell. Manuf..

[13]  Y. S. Tarng,et al.  Optimisation of the electrical discharge machining process using a GA-based neural network , 2003 .

[14]  Masanori Kunieda,et al.  Advancing EDM through fundamental insight into the process , 2005 .

[15]  Stephen T. Newman,et al.  State of the art electrical discharge machining (EDM) , 2003 .

[16]  Yang Dayong,et al.  The study of high efficiency and intelligent optimization system in EDM sinking process , 2004 .

[17]  R. K. Bhoi,et al.  Artificial Neural Network Prediction of Material Removal Rate in Electro Discharge Machining , 2005 .

[18]  Mukund R. Patel,et al.  Theoretical models of the electrical discharge machining process. I. A simple cathode erosion model , 1989 .

[19]  G. Krishna Mohana Rao,et al.  Development of hybrid model and optimization of surface roughness in electric discharge machining using artificial neural networks and genetic algorithm , 2009 .

[20]  N. Ramesh Babu,et al.  A neuro-genetic approach for selection of process parameters in abrasive waterjet cutting considering variation in diameter of focusing nozzle , 2008, Appl. Soft Comput..

[21]  S. Yeo,et al.  Critical assessment and numerical comparison of electro-thermal models in EDM , 2008 .

[22]  Surjya K. Pal,et al.  Flank wear prediction in drilling using back propagation neural network and radial basis function network , 2008, Appl. Soft Comput..

[23]  Shang-Liang Chen,et al.  Orthogonal least squares learning algorithm for radial basis function networks , 1991, IEEE Trans. Neural Networks.

[24]  S. S. Pande,et al.  Development of an intelligent process model for EDM , 2009 .

[25]  Shahin Rahimifard,et al.  STATE OF THE ART IN WIRE ELECTRICAL DISCHARGE MACHINING (WEDM) , 2004 .

[26]  Neelesh Kumar Jain,et al.  Optimization of process parameters of mechanical type advanced machining processes using genetic algorithms , 2007 .

[27]  Kalyanmoy Deb,et al.  A fast and elitist multiobjective genetic algorithm: NSGA-II , 2002, IEEE Trans. Evol. Comput..

[28]  G. Krishna Mohana Rao,et al.  DEVELOPMENT OF HYBRID MODEL AND OPTIMIZATION OF METAL REMOVAL RATE IN ELECTRIC DISCHARGE MACHINING USING ARTIFICIAL NEURAL NETWORKS AND GENETIC ALGORITHM , 2008 .

[29]  Qing Gao,et al.  Parameter optimization model in electrical discharge machining process , 2008 .

[30]  Kalyanmoy Deb,et al.  A Fast Elitist Non-dominated Sorting Genetic Algorithm for Multi-objective Optimisation: NSGA-II , 2000, PPSN.

[31]  Pei-Jen Wang,et al.  Predictions on surface finish in electrical discharge machining based upon neural network models , 2001 .

[32]  Dong-Mok Lee,et al.  Optimization of electric discharge machining using simulated annealing , 2009 .

[33]  Yi Wang,et al.  A hybrid intelligent method for modelling the EDM process , 2003 .