Deformation and failure mechanism of dynamically loaded sandwich beams with aluminum-foam core

Abstract In this paper the response and failure of dynamically loaded sandwich beams with an aluminum-foam core is investigated experimentally. The dynamic compressive stress–strain curves of the core material, an open-cell aluminum foam, are obtained by an SHPB technique. No strain-rate sensitivity is found. Quasi-static and dynamic bending tests are carried out for sandwich beams made of aluminum skins with an aluminum foam core. The deformation and failure mechanism are revealed by ‘frozen’ test using stop blocks. It is found that due to large local indentation and damage the energy absorbing capacity of beams loaded dynamically is lower than that for quasi-static loading.

[1]  U. Ramamurty,et al.  Strain rate sensitivity of a closed-cell aluminum foam , 2000 .

[2]  Hilary Bart-Smith,et al.  On the mechanical performance of closed cell Al alloy foams , 1997 .

[3]  M. Thompson,et al.  Density gradient effects on aluminium foam compression behaviour , 1997 .

[4]  Ronald E. Miller,et al.  Failure of sandwich beams with metallic foam cores , 2001 .

[5]  O. Hopperstad,et al.  Static and dynamic crushing of square aluminium extrusions with aluminium foam filler , 2000 .

[6]  Mamoru Mabuchi,et al.  Dynamic compression of an ultra-low density aluminium foam , 2000 .

[7]  Yasuo Yamada,et al.  Dynamic compressive behavior of an ultra-lightweight magnesium foam , 1999 .

[8]  J. Grenestedt,et al.  Influence of cell wall thickness variations on elastic stiffness of closed-cell cellular solids , 2000 .

[9]  N. Fleck,et al.  The plastic collapse of sandwich beams with a metallic foam core , 2001 .

[10]  N. Fleck,et al.  High strain rate compressive behaviour of aluminium alloy foams , 2000 .

[11]  Tomasz Wierzbicki,et al.  Bending crush resistance of partially foam-filled sections , 2000 .

[12]  Lorna J. Gibson,et al.  Effects of solid distribution on the stiffness and strength of metallic foams , 1998 .

[13]  M. Wolcott.  Cellular solids: Structure and properties , 1990 .

[14]  Tomasz Wierzbicki,et al.  Effect of an ultralight metal filler on the bending collapse behavior of thin-walled prismatic columns , 1999 .

[15]  M. Langseth,et al.  Bending of square aluminium extrusions with aluminium foam filler , 2000 .

[16]  Hilary Bart-Smith,et al.  Measurement and analysis of the structural performance of cellular metal sandwich construction , 2001 .

[17]  M. Ashby,et al.  Cellular solids: Structure & properties , 1988 .

[18]  Lorna J. Gibson,et al.  Size effects in metallic foam core sandwich beams , 2002 .

[19]  L. Gibson,et al.  The effects of cell face curvature and corrugations on the stiffness and strength of metallic foams , 1998 .

[20]  Mamoru Mabuchi,et al.  Experimental study of energy absorption in a close-celled aluminum foam under dynamic loading , 1999 .

[21]  J. Lankford,et al.  Strain Rate Effects in Porous Materials , 1998 .

[22]  M. Ashby,et al.  Sandwich Panel Design Using Aluminum Alloy Foam , 2000 .

[23]  O. Prakash,et al.  Structure and properties of AlSiC foam , 1995 .

[24]  Lorna J. Gibson,et al.  Compressive and tensile behaviour of aluminum foams , 1999 .

[25]  M. Ashby,et al.  The fatigue strength of sandwich beams with an aluminium alloy foam core , 2001 .