Age estimation of different tree species using a special kind of an electrically recording resistance drill

Abstract The determination of tree age is an important issue for urban green planning, forestry and dendrology; finding non-destructive and quasi-non-destructive methods for this purpose is of great theoretical and practical importance. The resistance drilling method is quasi-non-destructive because the average diameter of an opening that remains after drilling does not exceed 3 mm. Do electrically recording resistance drills allow precise assessment of tree age? The aim of this study is to assess the accuracy of determining the number of tree rings based on an examination of this special kind of drilling resistance profiles for three tree species, the pine Pinus sylvestris L., the oak Quercus robur L., and the birch Betula pendula ROTH. In 2015 and 2016, 15 pine trees, 15 oak trees, and 15 birch trees were randomly selected. For each studied tree, a measurement was conducted using the electrically recording resistance drill IML-Resi E400 with a flat-tipped 1.5/3 mm steel needle (research sample), and an increment core was taken (reference sample). The drill used was not a real Resistograph®. The analysis of the E400-profiles underestimated the number of tree rings; the mean bias error (MBE) values were –6.5, –2.5, and –6.0 years for pine, oak, and birch, respectively. The proportion of investigated trees with less than five years difference between the research and reference samples varied from 38.4 (birch) to 66.7 (oak) percent. The accuracy of tree age determination was lowest for birch and highest for oak. The binomial generalised linear model (GLM) revealed that the most accurate tree age assessments were obtained from tree rings wider than 2 mm. The measurements clearly showed that the electrically recording resistance drill IML-Resi E400 enables a quick, although approximate, tree age assessment. Future research should concentrate on electronically regulating and recording drills, providing a higher spatial and signal resolution, and a stronger correlation to wood density.

[1]  F. Schweingruber,et al.  RESISTOGRAPH and X-Ray Density Charts of Wood. Comparative Evaluation of Drill Resistance Profiles and X-ray Density Charts of Different Wood Species , 1996 .

[2]  Takuya Hiroshima,et al.  Applying age-based mortality analysis to a natural forest stand in Japan , 2014, Journal of Forest Research.

[3]  F. Larsen,et al.  Tilia's Physical Dimensions Over Time , 2002, Arboriculture & Urban Forestry.

[4]  Peter Niemz,et al.  Non-destructive testing of wood and wood-based materials , 2012 .

[5]  Robert J. Ross,et al.  A critical analysis of methods for rapid and nondestructive determination of wood density in standing trees , 2017, Annals of Forest Science.

[6]  Characteristics of Trees According to Community Population Level and by Land Use in the U.S. Midwest , 2002, Arboriculture & Urban Forestry.

[7]  Lars Linsen,et al.  Interactive Data Visualisation for Animating Urban Tree Growth , 2009 .

[8]  Frank Rinn.  Practical application of micro-resistance drilling for timber inspection , 2013 .

[9]  R Core Team,et al.  R: A language and environment for statistical computing. , 2014 .

[10]  Fikret Isik,et al.  Rapid assessment of wood density of live trees using the Resistograph for selection in tree improvement programs , 2003 .

[11]  Melanie Wetzig.  Untersuchungen zum Einfluss ausgewählter verfahrenstechnischer Parameter auf die VOC-Emission und ausgewählte mechanische Kennwerte wärmebehandelten Holzes , 2012 .

[12]  Allan Buras,et al.  Correcting the calculation of Gleichläufigkeit , 2015 .

[13]  M. Guz,et al.  Dynamika zmian szerokości przyrostów rocznych jako miara żywotności drzew w zadrzewieniach parkowych i zieleni miejskiej , 2012 .

[14]  Jerzy Jasieńko,et al.  In situ assessment of structural timber using the resistance drilling method – Evaluation of usefulness , 2016 .

[15]  Juan Su,et al.  Application of a Drill Resistance Technique for Rapid Determining Wood Density , 2009 .

[16]  R. Bruce Allison,et al.  Decay Detection in Red Oak Trees Using a Combination of Visual Inspection, Acoustic Testing, and Resistance Microdrilling , 2008, Arboriculture & Urban Forestry.

[17]  G. O'neill,et al.  An analysis of sensitivities contributing measurement error to Resistograph values , 2010 .

[18]  F. Rinn.  Intact-decay transitions in profiles of density-calibratable resistance drilling devices using long thin needles , 2016 .

[19]  C. Chiu,et al.  Application of the drilling resistance method for annual ring characteristics: evaluation of Taiwania (Taiwania cryptomerioides) trees grown with different thinning and pruning treatments , 2003, Journal of Wood Science.

[20]  M. Baillie,et al.  A SIMPLE CROSSDATING PROGRAM FOR TREE -RING RESEARCH , 1973 .

[21]  Sy-Dar Wang,et al.  Application of the drill resistance method for density boundary evaluation of earlywood and latewood of Taiwania (Taiwania cryptomerioides Hay.) plantation wood , 2001 .

[22]  R. Podlaski.  Modelowanie rozkładów pierśnic drzew z wykorzystaniem rozkładów mieszanych. II. Aproksymacja rozkładów pierśnic w lasach wielopiętrowych , 2011 .

[23]  J. Fox,et al.  Applied Regression Analysis and Generalized Linear Models , 2008 .

[24]  Determining The Age Of Streetside Tilia Cordata Trees With A Dbh-Based Model , 2005, Arboriculture & Urban Forestry.

[25]  F. S. Malan,et al.  A review of measurement methods used on standing trees for the prediction of some mechanical properties of timber , 2011, European Journal of Forest Research.