Two-Step Isothermal Bainitic Transformation in Medium-Carbon Low-Si Steels with Exceptional Mechanical Properties and Wear Resistance
暂无分享,去创建一个
[1] M. Dabalà,et al. Effect of Multi-Step Austempering Treatment on the Microstructure and Mechanical Properties of a High Silicon Carbide-Free Bainitic Steel with Bimodal Bainite Distribution , 2021, Metals.
[2] A. Mirak,et al. The effect of low temperature transformation time on microstructural & textural evolution, mechanical properties and fracture behavior of a low alloy, medium carbon, super strength AISI 4340 steel , 2021, Materials Science and Engineering: A.
[3] G. Tressia,et al. Improving the Mechanical Properties and Wear Resistance of a Commercial Pearlitic Rail Steel Using a Two-Step Heat Treatment , 2021, Metallurgical and Materials Transactions A.
[4] L. Bowen,et al. Sliding wear of medium-carbon bainitic/martensitic/austenitic steel treated by short-term low-temperature austempering , 2021, Wear.
[5] Avanish Kumar,et al. Mechanical properties of nanostructured bainitic steels , 2021 .
[6] H. J. Yang,et al. Effect of environments and normal loads on tribological properties of nitrided Ni45(FeCoCr)40(AlTi)15 high-entropy alloys , 2020 .
[7] Wei Liu,et al. Mechanical properties and wear resistance of ultrafine bainitic steel under low austempering temperature , 2020, International Journal of Minerals, Metallurgy and Materials.
[8] Guang Xu,et al. Effect of austempering time on microstructure and properties of a low-carbon bainite steel , 2020, International Journal of Minerals, Metallurgy and Materials.
[9] Wei Jiang,et al. Evolution of tribological mechanisms of nano-grained 304L stainless steel under dry and polyalphaolefin lubrication conditions , 2019, Materials Letters.
[10] A. P. Tschiptschin,et al. Assessment of tribological properties of plasma nitrided 410S ferritic-martensitic stainless steels , 2019, Wear.
[11] Y. Pei,et al. Microstructural and mechanical properties of low-carbon ultra-fine bainitic steel produced by multi-step austempering process , 2018, Materials Science and Engineering: A.
[12] Aparna Singh,et al. Tribological response and microstructural evolution of nanostructured bainitic steel under repeated frictional sliding , 2018, Wear.
[13] D. Chakrabarti,et al. Dry rolling/sliding wear behaviour of pearlitic rail and newly developed carbide-free bainitic rail steels , 2018, Wear.
[14] Leijun Li,et al. Instrumented indentation study of bainite/martensite duplex microstructure , 2018 .
[15] Wei Guo,et al. Quantitative assessment of carbon allocation anomalies in low temperature bainite , 2017 .
[16] A. Zhao,et al. Two-body abrasion wear mechanism of super bainitic steel , 2017 .
[17] F. C. Zhang,et al. Study on carbide-bearing and carbide-free bainitic steels and their wear resistance , 2017 .
[18] Kyung Il Kim,et al. Control of retained austenite morphology through double bainitic transformation , 2016 .
[19] P. Hodgson,et al. Comparisons of the two-body abrasive wear behaviour of four different ferrous microstructures with similar hardness levels , 2016 .
[20] X. Deng,et al. Epsilon carbide precipitation and wear behaviour of low alloy wear resistant steels , 2016 .
[21] Fucheng Zhang,et al. Low-cycle fatigue behavior and microstructural evolution in a low-carbon carbide-free bainitic steel , 2015 .
[22] F. Hu,et al. Multi-step isothermal bainitic transformation in medium-carbon steel , 2014 .
[23] P. Shipway,et al. Three-body abrasive wear of fine pearlite, nanostructured bainite and martensite , 2013 .
[24] V. G. Efremenko,et al. Impact–abrasive–corrosion wear of Fe-based alloys: Influence of microstructure and chemical composition upon wear resistance , 2013 .
[25] T. Sourmail,et al. Wear of nano-structured carbide-free bainitic steels under dry rolling–sliding conditions , 2013 .
[26] Z. Fucheng,et al. Wear property of low-temperature bainite in the surface layer of a carburized low carbon steel , 2011 .
[27] T. Wang,et al. Design of a new nanostructured, high-Si bainitic steel with lower cost production , 2011 .
[28] O. Bouaziz,et al. An approach to define the effective lath size controlling yield strength of bainite , 2010 .
[29] Han. Dong,et al. Characterization of microstructure obtained by quenching and partitioning process in low alloy martensitic steel , 2010 .
[30] C. Capdevila,et al. Redistribution of alloying elements during tempering of a nanocrystalline steel , 2008 .
[31] E. Pereloma,et al. Three-dimensional atom probe analysis of solute distribution in thermomechanically processed TRIP steels , 2007 .
[32] H. Bhadeshia,et al. Bimodal size-distribution of bainite plates , 2006 .
[33] C. Capdevila,et al. Design of Advanced Bainitic Steels by Optimisation of TTT Diagrams and T0 Curves , 2006 .
[34] Jien-Wei Yeh,et al. Adhesive wear behavior of AlxCoCrCuFeNi high-entropy alloys as a function of aluminum content , 2006 .
[35] C. K. Gupta,et al. A study of bainite transformation in a new CrMoV steel under continuous cooling conditions , 2005 .
[36] C. Bolfarini,et al. Sliding wear of spray-formed high-chromium white cast iron alloys , 2005 .
[37] E. Pereloma,et al. Effect of microstructure on the stability of retained austenite in transformation-induced-plasticity steels , 2004 .
[38] H. Bhadeshia,et al. Acceleration of Low-temperature Bainite , 2003 .
[39] H. Bhadeshia,et al. Low temperature bainite , 2003 .
[40] H. Bhadeshia,et al. Development of Hard Bainite , 2003 .
[41] Francisca García Caballero,et al. Very strong low temperature bainite , 2002 .
[42] H. Bhadeshia,et al. Strength of mixtures of bainite and martensite , 1994 .
[43] A. R. Rosenfield,et al. Wear processes in sliding systems , 1984 .
[44] H. K. D. H. Bhadeshia,et al. Bainite in silicon steels: New composition–property approach Part 1 , 1983 .