Emulation of Non-Reciprocity applied in Load-Modulated Power Amplifier Architectures using Single Amplifier Load-Pull Measurements

An active load-pull measurement technique is exploited to test the performance of novel high-efficiency power amplifier (PA) concepts based on non-reciprocity. This technique allows new PA architectures, including its load-modulation, to be evaluated before any construction is necessary. Merely active load -pull measurements of a single representative device or PA, in combination with knowledge of the S-parameters of the output combiner, are needed. As a result of the technique, the load modulation on the branch PAs are exposed, thereby allowing PA designers to optimize PA performance. The technique is demonstrated by emulating a load-modulation PA, consisting of two branch PAs with their outputs combined using a non-reciprocal circulator. The resulting PA concept is designed and evaluated at 2.14 GHz.

[1]  C. Fager,et al.  Circulator Load Modulated Amplifier: A Non-Reciprocal Wideband and Efficient PA Architecture , 2021, 2021 IEEE MTT-S International Microwave Symposium (IMS).

[2]  P. Zampardi,et al.  Emulation of a Multi-Stage Differential Amplifier Using one Single-Ended Device-Under-Test , 2021, ARFTG Microwave Measurement Conference.

[3]  P. Zampardi,et al.  Mixed-Mode Active Load-Pull Using one Single-Ended Device-Under-Test , 2021, 2021 IEEE Topical Conference on RF/Microwave Power Amplifiers for Radio and Wireless Applications (PAWR).

[4]  K. Buisman,et al.  An Active Load-Pull Technique to Emulate Outphasing Power Amplifiers , 2021, 2021 IEEE Topical Conference on RF/Microwave Power Amplifiers for Radio and Wireless Applications (PAWR).

[5]  Christian Fager,et al.  Emulation of Doherty Amplifiers Using Single- Amplifier Load–Pull Measurements , 2020, IEEE Microwave and Wireless Components Letters.

[6]  R. Hou,et al.  The Continuum of Load Modulation Ratio From Doherty to Traveling-Wave Amplifiers , 2019, IEEE Transactions on Microwave Theory and Techniques.

[7]  Christian Fager,et al.  Linearity and Efficiency in 5G Transmitters: New Techniques for Analyzing Efficiency, Linearity, and Linearization in a 5G Active Antenna Transmitter Context , 2019, IEEE Microwave Magazine.

[8]  Koen Buisman,et al.  Measurement Technique to Emulate Signal Coupling Between Power Amplifiers , 2018, IEEE Transactions on Microwave Theory and Techniques.

[9]  Koen Buisman,et al.  An active load-pull technique creating time-variant impedances to emulate coupling between power amplifiers , 2017, 2017 IEEE MTT-S International Microwave Symposium (IMS).

[10]  Koen Buisman,et al.  Emulation of array coupling influence on RF power amplifiers in a measurement setup , 2016, 2016 87th ARFTG Microwave Measurement Conference (ARFTG).

[11]  Steve C. Cripps,et al.  An Efficient Broadband Reconfigurable Power Amplifier Using Active Load Modulation , 2016, IEEE Microwave and Wireless Components Letters.

[12]  Erik G. Larsson,et al.  Massive MIMO for next generation wireless systems , 2013, IEEE Communications Magazine.

[13]  W.H. Doherty,et al.  A New High Efficiency Power Amplifier for Modulated Waves , 1936, Proceedings of the Institute of Radio Engineers.

[14]  H. Chireix.  High Power Outphasing Modulation , 1935, Proceedings of the Institute of Radio Engineers.

[15]  Anh-Vu Pham,et al.  A Doherty Amplifier With Modified Load Modulation Scheme Based on Load–Pull Data , 2018, IEEE Transactions on Microwave Theory and Techniques.