Dual gas jet-assisted fibre laser blind cutting of dry pine wood by statistical modelling

This paper presents a statistical analysis of the performance of an Ytterbium fibre laser utilising single and dual gas jets in a single pass to blind cut dry pine wood. Cutting wood with lasers is a multi-factor process and a proper combination of the parameters involved is needed to achieve high quality and optimum process efficiency. This study employs design of experiments and statistical modelling approach to investigate the significant process parameters along with their interactions. A high brightness, 1 kW IPG single mode Ytterbium-doped fibre laser was employed to produce blind cuts on samples of dry pine wood. The experiments were performed parallel to the direction of the wood fibre. The parameters investigated include laser power, focal plane position, traverse speed, gas pressure and single and dual gas jets. Results were compared using a number of process responses which define the efficiency of the cut in terms of kerf depth, mass removal and energy consumption as well as quality of the cut section considering the heat-affected zone, kerf width and roughness of the edge of the surface. It has been found that application of an additional gas jet produced a surface finish superior to the single jet.

[1]  Choon-Man Lee,et al.  A study on the optimal cutting condition of a high speed feeding type laser cutting machine by using Taguchi method , 2006 .

[2]  Charles W. McMillin,et al.  Factors influencing laser cutting of wood , 1986 .

[3]  J. Powell.  CO[2] laser cutting , 1993 .

[4]  W. Steen.  Laser Material Processing , 1991 .

[5]  C. Yang,et al.  Study of optimal laser parameters for cutting QFN packages by Taguchi's matrix method , 2007 .

[6]  Biswanath Doloi,et al.  Optimization of process parameters of Nd:YAG laser microgrooving of Al2TiO5 ceramic material by response surface methodology and artificial neural network algorithm , 2007 .

[7]  G. Derringer,et al.  Simultaneous Optimization of Several Response Variables , 1980 .

[8]  Margarida C. Pires,et al.  Plywood Inlays Thourgh CO2 Laser Cutting , 1989, Photonics West - Lasers and Applications in Science and Engineering.

[9]  S. L. Ng,et al.  CO2 laser cutting of MDF: 1. Determination of process parameter settings , 2000 .

[10]  Stephan Barcikowski,et al.  Laser cutting and joining of wooden materials: How both processes are determined by the heat affected zone , 2006 .

[11]  Lin Li,et al.  High-power Yb-doped Fibre Laser for Cutting Dry Pine Wood , 2007, World Congress on Engineering.

[12]  V. Yadava,et al.  Multi-objective optimisation of laser beam cutting process , 2008 .

[13]  J. Powell.  CO2 Laser Cutting , 1993 .

[14]  Stephan Barcikowski,et al.  Laser cutting of wood and wood composites - evaluation of cut quality and comparison to conventional wood cutting techniques , 2004 .

[15]  S. J. Hyder,et al.  The Taguchi method for determining CO2 laser cut quality , 1998 .

[16]  K. Mukherjee,et al.  Focal point location in laser machining of thick hard wood , 1994 .

[17]  J. Anderson,et al.  Fundamentals of Aerodynamics , 1984 .

[18]  G. Verhaeghe.  The fiber laser: A newcomer for material welding and cutting , 2005 .

[19]  Lennie E. N. Lim,et al.  Application of Taguchi methods in the optimization of the laser-cutting process , 1992 .

[20]  Shang-Liang Chen.  The effects of high-pressure assistant-gas flow on high-power CO2 laser cutting , 1999 .

[21]  G. Tsoumis,et al.  Science and technology of wood : structure, properties, utilization , 1991 .

[22]  H. E. Desch,et al.  Timber: Structure, Properties, Conversion and Use , 1996 .

[23]  Valentin Gapontsev.  Ultra high power Ytterbium fiber lasers , 2004 .

[24]  Juan Carlos Hernandez-Castaneda,et al.  Statistical analysis of ytterbium-doped fibre laser cutting of dry pine wood , 2009 .

[25]  Charles W. McMillin,et al.  Laser machining wood composites , 1989 .

[26]  Charles W. McMillin,et al.  Gas flow parameters in laser cutting of wood―nozzle design , 1990 .

[27]  Douglas C. Montgomery,et al.  Response Surface Methodology: Process and Product Optimization Using Designed Experiments , 1995 .

[28]  W. J. Witteman,et al.  The CO2 Laser , 1987 .

[29]  Lin Li,et al.  A statistical analysis of striation formation during laser cutting of ceramics , 2008 .

[30]  W. J. Witteman.  The CO「下2下」 laser , 1987 .

[31]  Frank W. Jane,et al.  The structure of wood , 1956 .

[32]  M. J. Malachowski.  Trimming trees using a high power CO2 laser: Machining of green and dry wood , 1984 .

[33]  S. Barcikowski,et al.  Characterisation and modification of the heat affected zone during laser material processing of wood and wood composites , 2006, Holz als Roh- und Werkstoff.

[34]  J. E. Harry,et al.  Laser machining of southern pine , 1971 .

[35]  N. Naderi,et al.  Preliminary investigations of ultrafast intense laser wood processing , 1999 .