Identification of elastic properties of human patellae using micro-finite element analysis.

Current homogenized finite element (hFE) models of the patella lack a validated material law and mostly overlook trabecular anisotropy. The objective of this study was to identify the elastic constants of patellar trabecular bone. Using μCT scans of 20 fresh-frozen cadaveric patellae, we virtually extracted 200 trabecular cubes (5.3mm side length). Bone volume fraction and fabric tensor were measured. The elastic constants were identified from six independent load cases using micro finite element (μFE) analyses. Both anisotropic and isotropic material laws were considered. The elastic constants were validated by comparing stiffness, strain and stress between hFE and μFE predictions of 18 patellar sections and six load cases. The hFE section models were built from μCT (anisotropic law) and CT (isotropic law) scans. The homogenized anisotropic model induced less error (13±5%) in the global stiffness prediction than the isotropic one (18±6%), and less error in the prediction of local apparent strain, stress, and strain energy, compared to the isotropic one. This validated hFE model could be used for future applications, either with the anisotropic constants, or with the isotropic ones when the trabecular fabric is unavailable.

[1]  C. Powers,et al.  Comparison of patella bone strain between females with and without patellofemoral pain: a finite element analysis study. , 2014, Journal of biomechanics.

[2]  P. Zysset,et al.  Mineral heterogeneity has a minor influence on the apparent elastic properties of human cancellous bone: a SRμCT-based finite element study , 2012, Computer methods in biomechanics and biomedical engineering.

[3]  F. Taddei,et al.  A novel approach to estimate trabecular bone anisotropy using a database approach. , 2013, Journal of biomechanics.

[4]  W. J. Whitehouse.  The quantitative morphology of anisotropic trabecular bone , 1974, Journal of microscopy.

[5]  F. Eckstein,et al.  Estimation of distal radius failure load with micro-finite element analysis models based on three-dimensional peripheral quantitative computed tomography images. , 2002, Bone.

[6]  R M Rose,et al.  Trabecular architecture of the human patella. , 1975, Journal of biomechanics.

[7]  Mauricio Reyes,et al.  Biomechanical Role of Bone Anisotropy Estimated on Clinical CT Scans by Image Registration , 2016, Annals of Biomedical Engineering.

[8]  P. Zysset,et al.  Finite element analysis for prediction of bone strength. , 2013, BoneKEy reports.

[9]  Philippe K. Zysset,et al.  An alternative model for anisotropic elasticity based on fabric tensors , 1995 .

[10]  J. H. Steiger.  Tests for comparing elements of a correlation matrix. , 1980 .

[11]  Maarten Moesen,et al.  A symmetry invariant formulation of the relationship between the elasticity tensor and the fabric tensor. , 1985, Mechanics of materials : an international journal.

[12]  Lowell M. Smoger,et al.  Effects of resection thickness on mechanics of resurfaced patellae. , 2013, Journal of biomechanics.

[13]  P. Zysset,et al.  Influence of boundary conditions on computed apparent elastic properties of cancellous bone , 2008, Biomechanics and modeling in mechanobiology.

[14]  Keita Ito,et al.  A new approach to determine the accuracy of morphology-elasticity relationships in continuum FE analyses of human proximal femur. , 2012, Journal of biomechanics.

[15]  L. Lin,et al.  A concordance correlation coefficient to evaluate reproducibility. , 1989, Biometrics.

[16]  F. Becce,et al.  A patient-specific model of total knee arthroplasty to estimate patellar strain: A case study. , 2016, Clinical biomechanics.

[17]  H. Redkey,et al.  A new approach. , 1967, Rehabilitation record.

[18]  B. van Rietbergen,et al.  A survey of micro-finite element analysis for clinical assessment of bone strength: the first decade. , 2015, Journal of biomechanics.

[19]  P. Zysset,et al.  A comparison of enhanced continuum FE with micro FE models of human vertebral bodies. , 2009, Journal of biomechanics.

[20]  Christian Huet,et al.  Order relationships for boundary conditions effect in heterogeneous bodies smaller than the representative volume , 1994 .

[21]  Clare K Fitzpatrick,et al.  Comparison of patellar bone strain in the natural and implanted knee during simulated deep flexion , 2011, Journal of orthopaedic research : official publication of the Orthopaedic Research Society.

[22]  P. Rüegsegger,et al.  In vivo high resolution 3D-QCT of the human forearm. , 1998, Technology and health care : official journal of the European Society for Engineering and Medicine.

[23]  P. Rüegsegger,et al.  Direct Three‐Dimensional Morphometric Analysis of Human Cancellous Bone: Microstructural Data from Spine, Femur, Iliac Crest, and Calcaneus , 1999, Journal of bone and mineral research : the official journal of the American Society for Bone and Mineral Research.

[24]  J. Jurvelin,et al.  Prediction of mechanical properties of trabecular bone using quantitative MRI , 2006, Physics in medicine and biology.

[25]  P. Zysset,et al.  Bone Volume Fraction and Fabric Anisotropy Are Better Determinants of Trabecular Bone Stiffness Than Other Morphological Variables , 2015, Journal of bone and mineral research : the official journal of the American Society for Bone and Mineral Research.

[26]  Philippe K Zysset,et al.  A review of morphology-elasticity relationships in human trabecular bone: theories and experiments. , 2003, Journal of biomechanics.

[27]  P. Zysset,et al.  Valid micro finite element models of vertebral trabecular bone can be obtained using tissue properties measured with nanoindentation under wet conditions. , 2010, Journal of biomechanics.

[28]  E. Itoi,et al.  Patellar morphology and femoral component geometry influence patellofemoral contact stress in total knee arthroplasty without patellar resurfacing , 2012, Knee Surgery, Sports Traumatology, Arthroscopy.

[29]  T. W. Ridler,et al.  Picture thresholding using an iterative selection method. , 1978 .

[30]  P. Zysset,et al.  Morphology–elasticity relationships using decreasing fabric information of human trabecular bone from three major anatomical locations , 2012, Biomechanics and Modeling in Mechanobiology.

[31]  Maarten Moesen,et al.  A symmetry invariant formulation of the relationship between the elasticity tensor and the fabric tensor , 2012 .

[32]  W. Alexander,et al.  The American society for bone and mineral research , 1987, Steroids.