The role of adhesive in the ballistic/structural performance of ceramic/polymer–matrix composite hybrid armor

Abstract Transient non-linear dynamics computational finite-element analyses are employed to investigate the role of the adhesive used in ceramic strike-face/composite back-face hybrid armor. The role of the adhesive is investigated under: (a) high loading-rate conditions accompanying impact of an armor-piercing projectile onto the armor structure; and (b) low loading rate conditions associated with the ingress of the loads which are generated at the road/tire contact interfaces and transmitted into the armor structure through the vehicle frame. The high loading-rate conditions were analyzed since they reveal the role of the adhesive under ballistic impact scenarios which controls the overall penetration resistance of the armor. On the other hand, the low loading-rate conditions were analyzed since they may reveal the potential structural damage that armor may experience due to sustained in-service loads. Since structural thermoset-polymer-based adhesives suffer from inadequate ductility, only the case of flexible (elastomer-based) adhesives was considered. The following two specific aspects of the adhesive mechanical response are given special attention: (a) strain rate sensitivity and (b) the degree of volumetric compressibility. The results obtained show that while significant improvements in the ballistic protection performance and durability of hybrid armor can be attained by proper modifications in the adhesive layer mechanical properties, there is no single combination of these properties which simultaneously optimizes all the performance requirements.

[1]  M. Grujicic,et al.  Material‐modeling and structural‐mechanics aspects of the traumatic brain injury problem , 2010 .

[2]  K. Ramanjaneyulu,et al.  An experimental study of penetration resistance of ceramic armour subjected to projectile impact , 2005 .

[3]  Z. Rozenberg,et al.  The relation between ballastic efficiency and compressive strength of ceramic tiles , 1988 .

[4]  John W. Gillespie,et al.  Co-Injection Resin Transfer Molding for Optimization of Integral Armor , 1998 .

[5]  W. C. Bell,et al.  Inclusion of material non-linearity and inelasticity into a continuum-level material model for soda–lime glass , 2012 .

[6]  E. Medvedovski.  Alumina ceramics for ballistic protection. Part 1 , 2002 .

[7]  G. Settles,et al.  Experimental Characterization and Material-Model Development for Microphase-Segregated Polyurea: An Overview , 2011, Journal of Materials Engineering and Performance.

[8]  W. C. Bell,et al.  The effect of high-pressure densification on ballistic-penetration resistance of a soda-lime glass , 2011 .

[9]  M. Aghajanian,et al.  A new family of reaction bonded ceramics for armor applications , 2002 .

[10]  W. C. Bell,et al.  Fluid/Structure Interaction Computational Investigation of Blast-Wave Mitigation Efficacy of the Advanced Combat Helmet , 2011 .

[11]  G. R. Johnson,et al.  Fracture characteristics of three metals subjected to various strains, strain rates, temperatures and pressures , 1985 .

[12]  Ernest S. C. Chin,et al.  Army focused research team on functionally graded armor composites , 1999 .

[13]  M. Grujicic,et al.  Computational Investigation of Impact Energy Absorption Capability of Polyurea Coatings via Deformation-Induced Glass Transition , 2010 .

[14]  Mica Grujicic,et al.  Ballistic Performance of Alumina/S‐2 Glass‐reinforced Polymer‐matrix Composite Hybrid Lightweight Armor Against Armor Piercing (ap) and Non‐AP Projectiles , 2007 .

[15]  Mica Grujicic,et al.  Material Modeling and Ballistic-Resistance Analysis of Armor-Grade Composites Reinforced with High-Performance Fibers , 2009, Journal of Materials Engineering and Performance.

[16]  Mica Grujicic,et al.  Parameterization of the porous-material model for sand with different levels of water saturation , 2008 .

[17]  Mica Grujicic,et al.  Computational investigation of the effect of up-armouring on the reduction in occupant injury or fatality in a prototypical high-mobility multi-purpose wheeled vehicle subjected to mine blast , 2009 .

[18]  W. C. Bell,et al.  The effect of a carbon-nanotube forest-mat strike face on the ballistic-protection performance of E-glass reinforced poly-vinyl-ester-epoxy composite armour , 2008 .

[19]  S. Sánchez-Sáez,et al.  Modelling of the adhesive layer in mixed ceramic/metal armours subjected to impact , 2000 .

[20]  Mica Grujicic,et al.  A ballistic material model for cross-plied unidirectional ultra-high molecular-weight polyethylene fiber-reinforced armor-grade composites , 2008 .

[21]  D. Agard,et al.  Microtubule nucleation by γ-tubulin complexes , 2011, Nature Reviews Molecular Cell Biology.

[22]  M. Grujicic,et al.  A computational analysis of the ballistic performance of light-weight hybrid composite armors , 2006 .

[23]  W. C. Bell,et al.  Blast-wave impact-mitigation capability of polyurea when used as helmet suspension-pad material , 2010 .

[24]  Graham Williams,et al.  Anelastic and Dielectric Effects in Polymeric Solids , 1991 .

[25]  S. Nemat-Nasser,et al.  An experimentally-based viscoelastic constitutive model for polyurea, including pressure and temperature effects , 2006 .

[26]  D. J. Viechnicki,et al.  DEVELOPMENT AND CURRENT STATUS OF ARMOR CERAMICS , 1991 .