Fabrication of gas diffusion layer based on x–y robotic spraying technique for proton exchange membrane fuel cell application

Abstract The x–y robotic spraying technique developed in the Universiti Kebangsaan Malaysia is capable of fabricating various sizes of thickness and porosity of gas diffusion layer (GDL) used in the proton exchange membrane fuel cell (PEMFC). These parameters are obtained by varying the characteristic spray numbers of the robotic spraying machine. This investigation results were adequately represented with mathematical equations for hydrogen gas distribution in GDL. Volumetric modulus ( M ) parameter is used to determine the value of current density produced on the electrode of a single cell PEMFC. Thus the M parameter can be employed as indicator for a successful GDL fabrication. GDL type 4 has three variables of layer design that can be optimized to function as gas distributor, gas storage, flooding preventer on GDL surface, to evacuate water from the electrode and to control the electrical conductivity. The gas distribution in GDL was mathematically represented with average error of 15.5%. The M value of GDL type 4 according to the model was 0.22 cm 3 /s and yielded a current density of 750 A/m 2 .

[1]  Xianguo Li,et al.  Mathematical modeling of proton exchange membrane fuel cells , 2001 .

[2]  Edson A. Ticianelli,et al.  Methods to Advance Technology of Proton Exchange Membrane Fuel Cells , 1988 .

[3]  Ned Djilali,et al.  A two-dimensional analysis of mass transport in proton exchange membrane fuel cells , 1999 .

[4]  Shanhai Ge,et al.  A mathematical model for PEMFC in different flow modes , 2003 .

[5]  Tien-Chien Jen,et al.  Chemical reacting transport phenomena in a PEM fuel cell , 2003 .

[6]  Tae-Hee Lee,et al.  Influence of pore-size distribution of diffusion layer on mass-transport problems of proton exchange membrane fuel cells , 2002 .

[7]  Xianguo Li,et al.  Modelling of polymer electrolyte membrane fuel cells with variable degrees of water flooding , 2000 .

[8]  K. M. Chittajallu,et al.  Design and optimization of polymer electrolyte membrane (PEM) fuel cells , 2004 .

[9]  Wetting, spreading and adhesion , 1979 .

[10]  T. Nguyen,et al.  A liquid water management strategy for PEM fuel cell stacks , 2003 .

[11]  Edson A. Ticianelli,et al.  Development and electrochemical studies of gas diffusion electrodes for polymer electrolyte fuel cells , 1996 .

[12]  Shigeru Sakamoto.  Mecanical planning and Actual Result of Painting Robot for High Rised Building , 1990 .

[13]  Abu Bakar Mohamad,et al.  Improved membrane and electrode assemblies for proton exchange membrane fuel cells , 2003 .

[14]  O. Savadogo.  Emerging membranes for electrochemical systems: Part II. High temperature composite membranes for polymer electrolyte fuel cell (PEFC) applications☆ , 2004 .

[15]  Hongtan Liu,et al.  A parametric study of the cathode catalyst layer of PEM fuel cells using a pseudo-homogeneous model , 2001 .

[16]  Jin Hyun Nam,et al.  Effective diffusivity and water-saturation distribution in single- and two-layer PEMFC diffusion medium , 2003 .

[17]  Falin Chen,et al.  Effects of porosity change of gas diffuser on performance of proton exchange membrane fuel cell , 2003 .

[18]  Anzhong Gu,et al.  Three dimensional, two phase flow mathematical model for PEM fuel cell: Part II. Analysis and discussion of the internal transport mechanisms , 2004 .

[19]  S. Litster,et al.  PEM fuel cell electrodes , 2004 .

[20]  S. Middleman,et al.  An Introduction to Mass and Heat Transfer: Principles of Analysis and Design , 1997 .

[21]  M. Hori,et al.  Novel gas diffusion layer with water management function for PEMFC , 2004 .

[22]  Sadik Kakac,et al.  Two‐dimensional model for proton exchange membrane fuel cells , 1998 .