Design and Experimental Analysis of a Medium-Frequency Transformer for Solid-State Transformer Applications

Within a solid-state transformer, the isolated dc–dc converter and in particular its medium-frequency transformer are one of the critical components, as it provides the required isolation between primary and secondary sides and the voltage conversion typically necessary for the operation of the system. A comprehensive optimization procedure is required to find a transformer design that maximizes power density and efficiency within the available degrees of freedom while complying with material limits, such as temperature, flux density, and dielectric strength as well as outer dimension limits. This paper presents an optimization routine and its underlying loss and thermal models, which are used to design a 166 kW/20 kHz transformer prototype achieving 99.4% efficiency at a power density of 44 kW/dm3. Extensive measurements are performed on the constructed prototype in order to measure core and winding losses and to investigate the current distribution within the litz wire and the flux sharing between the cores.

[1]  Jan Abraham Ferreira,et al.  Improved analytical modeling of conductive losses in magnetic components , 1994 .

[2]  Charles R. Sullivan.  Optimal choice for number of strands in a litz-wire transformer winding , 1997 .

[3]  L. Heinemann,et al.  The universal power electronics based distribution transformer, an unified approach , 2001, 2001 IEEE 32nd Annual Power Electronics Specialists Conference (IEEE Cat. No.01CH37230).

[4]  Charles R. Sullivan,et al.  Accurate prediction of ferrite core loss with nonsinusoidal waveforms using only Steinmetz parameters , 2002, 2002 IEEE Workshop on Computers in Power Electronics, 2002. Proceedings..

[5]  Alex Van den Bossche,et al.  Inductors and Transformers for Power Electronics , 2005 .

[6]  J.A. Ferreira,et al.  Design for better thermal management in high-power high-frequency transformers , 2005, Fourtieth IAS Annual Meeting. Conference Record of the 2005 Industry Applications Conference, 2005..

[7]  K. Frohlich,et al.  Electrical breakdown in high-voltage winding insulations of different manufacturing qualities , 2006, IEEE Electrical Insulation Magazine.

[8]  Johann W. Kolar,et al.  Cooling Concepts for High Power Density Magnetic Devices , 2007 .

[9]  H. Akagi,et al.  A Bidirectional Isolated DC–DC Converter as a Core Circuit of the Next-Generation Medium-Voltage Power Conversion System , 2007, IEEE Transactions on Power Electronics.

[10]  J. Lobry,et al.  Multiobjective optimal design of high frequency transformers using genetic algorithm , 2009, 2009 13th European Conference on Power Electronics and Applications.

[11]  J.A. Ferreira,et al.  Reaching High Power Density in Multikilowatt DC–DC Converters With Galvanic Isolation , 2009, IEEE Transactions on Power Electronics.

[12]  A. Miraoui,et al.  Smart-grid technologies and progress in Europe and the USA , 2011, 2011 IEEE Energy Conversion Congress and Exposition.

[13]  Ion Etxeberria-Otadui,et al.  Proposal and validation of medium-frequency power transformer design methodology , 2011, 2011 IEEE Energy Conversion Congress and Exposition.

[14]  J. W. Kolar,et al.  Strategies to reduce copper losses in connections of medium-frequency high-current converters , 2011, IECON 2011 - 37th Annual Conference of the IEEE Industrial Electronics Society.

[15]  J. W. Kolar,et al.  Loss modeling of inductive components employed in power electronic systems , 2011, 8th International Conference on Power Electronics - ECCE Asia.

[16]  Johann W. Kolar,et al.  Overview and Comparison of Grid Harmonics and Conducted EMI Standards for LV Converters Connected to the MV Distribution System , 2012 .

[17]  J. W. Kolar,et al.  Modeling of Soft-Switching Losses of IGBTs in High-Power High-Efficiency Dual-Active-Bridge DC/DC Converters , 2013, IEEE Transactions on Electron Devices.

[18]  J. W. Kolar,et al.  η-ρ Pareto optimization of bidirectional half-cycle discontinuous-conduction-mode series-resonant DC/DC converter with fixed voltage transfer ratio , 2013, 2013 Twenty-Eighth Annual IEEE Applied Power Electronics Conference and Exposition (APEC).

[19]  Charles R. Sullivan,et al.  Simplified design method for litz wire , 2014, 2014 IEEE Applied Power Electronics Conference and Exposition - APEC 2014.

[20]  Johann W. Kolar,et al.  Comparative analysis of inductor concepts for high peak load low duty cycle operation , 2014, 2014 International Power Electronics Conference (IPEC-Hiroshima 2014 - ECCE ASIA).

[21]  Charles R. Sullivan,et al.  Analytical model for effects of twisting on litz-wire losses , 2014, 2014 IEEE 15th Workshop on Control and Modeling for Power Electronics (COMPEL).

[22]  Scott D. Sudhoff.  Power Magnetic Devices , 2014 .

[23]  Johann W. Kolar,et al.  Volume/weight/cost comparison of a 1MVA 10 kV/400 V solid-state against a conventional low-frequency distribution transformer , 2014, 2014 IEEE Energy Conversion Congress and Exposition (ECCE).

[24]  Johann W. Kolar,et al.  Solid-State-Transformers: Key Components of Future Traction and Smart Grid Systems , 2014 .

[25]  Scott D. Sudhoff,et al.  Power Magnetic Devices: A Multi-Objective Design Approach , 2014 .

[26]  Giorgio Sulligoi,et al.  Power electronics for all-electric ships with MVDC power distribution system: An overview , 2014, 2014 Ninth International Conference on Ecological Vehicles and Renewable Energies (EVER).

[27]  Juan C. Vasquez,et al.  Advanced LVDC Electrical Power Architectures and Microgrids: A step toward a new generation of power distribution networks. , 2014, IEEE Electrification Magazine.

[28]  Gabriel Ortiz.  High-Power DC-DC Converter Technologies for Smart Grid and Traction Applications , 2014 .

[29]  A. Pereira,et al.  Comparison between numerical and analytical methods of AC resistance evaluation for Medium Frequency Transformers: Validation on a prototype , 2015, 2015 IEEE Electrical Power and Energy Conference (EPEC).

[30]  Johann W. Kolar,et al.  Protection of MV/LV solid-state transformers in the distribution grid , 2015, IECON 2015 - 41st Annual Conference of the IEEE Industrial Electronics Society.