On the origin of sliver defects in single crystal investment castings

Abstract The origin of sliver defects in seeded single crystal castings has been determined to be the deformation of dendrites in the mushy zone through microstructural characterization of a series of castings with a geometry sensitive to these defects. The extent of bending and torsion of the dendrites in the as-cast microstructure and the net misorientation was quantified from electron backscattered diffraction data using a bespoke data analysis method. At the point of initiation of the sliver defects, deformation was localized at the mould wall, indicating that these defects arise as a result of the bending moments generated by differential thermal contraction between the mould and the dendrites. The comparative susceptibilities of dendrites to deformation under converging and diverging growth with respect to the mould wall were distinguished. The experimental observations were supported by continuum finite element simulations using ProCAST™, which confirmed the occurrence of high stresses in the constricted channel where sliver defects form. Contrary to foundry wisdom, ancillary observations demonstrated that the oxide at the seed melt-back interface played no role.

[1]  Lars Arnberg,et al.  In situ observations of dendritic fragmentation due to local solute-enrichment during directional solidification of an aluminum alloy , 2007 .

[2]  R. W. Balluffi,et al.  Interfaces in crystalline materials , 2009 .

[3]  Yizhou Zhou,et al.  Formation of stray grains during directional solidification of a nickel-based superalloy , 2011 .

[4]  G. Fuchs,et al.  Effect of carbon additions on the as-cast microstructure and defect formation of a single crystal Ni-based superalloy , 2004 .

[5]  J. Pośpiech,et al.  Some Information on Quaternions Useful in Texture Calculations , 1989 .

[6]  Tomohiro Takaki,et al.  Numerical investigations of stress in dendrites caused by gravity , 2011 .

[7]  H. Nguyen-Thi,et al.  Tailoring of dendritic microstructure in solidification processing by crucible vibration , 2005 .

[8]  R. Reed,et al.  Recrystallisation of single crystal superalloy CMSX–4 , 2003 .

[9]  Christoph Beckermann,et al.  Modeling of micro- and macrosegregation and freckle formation in single-crystal nickel-base superalloy directional solidification , 1997 .

[10]  M. Tiryakioğlu,et al.  Bifilm Defects in Ni-Based Alloy Castings , 2012, Metallurgical and Materials Transactions B.

[11]  P. Grant,et al.  Solidification in Spray Forming , 2007 .

[12]  R. Trivedi,et al.  Solidification microstructures and solid-state parallels: Recent developments, future directions , 2009 .

[13]  M. Worster.  Instabilities of the liquid and mushy regions during solidification of alloys , 1992, Journal of Fluid Mechanics.

[14]  B. Billia,et al.  Cumulative mechanical moments and microstructure deformation induced by growth shape in columnar solidification. , 2004, Physical review letters.

[15]  P. Lee,et al.  Seeding of single-crystal superalloys—Role of constitutional undercooling and primary dendrite orientation on stray-grain nucleation and growth , 2005 .

[16]  T. Pollock,et al.  Modeling fluid flow in three-dimensional single crystal dendritic structures , 2010 .

[17]  Peter D. Lee,et al.  Simulation of stray grain formation during single crystal seed melt-back and initial withdrawal in the Ni-base superalloy CMSX4 , 2005 .

[18]  P. Voorhees,et al.  Pinch-off of rods by bulk diffusion , 2011 .

[19]  C. Woodward,et al.  Ab initio simulations of molten Ni alloys , 2010 .

[20]  B. Shollock,et al.  Seeding of single crystal superalloys: role of seed melt-back on casting defects , 2004 .

[21]  A. F. Giamei,et al.  The origin of freckles in unidirectionally solidified castings , 1970 .

[22]  D. Seidman,et al.  The role of hafnium in the formation of misoriented defects in Ni-based superalloys: An atom-probe tomographic study , 2011 .

[23]  Dendrite fragmentation by catastrophic elastic remelting , 2008, 0810.2017.

[24]  J. Aveson.  Studying flow effects on dendrite fragmentation using Rayleigh–Bénard convection , 2012 .

[25]  J. Lacaze,et al.  Dendritic growth and crystalline quality of nickel-base single grains , 1993 .

[26]  P. D. Lee,et al.  Stray grain formation in the seed region of single-crystal turbine blades , 2005 .

[27]  J. Baruchel,et al.  In-Situ and Real-Time Analysis of the Formation of Strains and Microstructure Defects during Solidification of Al-3.5 Wt Pct Ni Alloys , 2008 .

[28]  John L. Campbell,et al.  The Origin of Griffith Cracks , 2011 .

[29]  D. Seidman,et al.  An atom-probe tomographic study of freckle formation in a nickel-based superalloy , 2011 .

[30]  S. Altmann.  Rotations, Quaternions, and Double Groups , 1986 .

[31]  M. E. Shank,et al.  The development of columnar grain and single crystal high temperature materials through directional solidification , 1970 .

[32]  J. Driver,et al.  Orientation distribution analysis in deformed grains , 2001 .

[33]  C. Beckermann,et al.  Simulation of solid deformation during solidification: Shearing and compression of polycrystalline structures , 2013 .

[34]  C. Gandin,et al.  Process modelling of grain selection during the solidification of single crystal superalloy castings , 2000 .

[35]  G. Fuchs.  Solution heat treatment response of a third generation single crystal Ni-base superalloy , 2001 .

[36]  R. Reed.  The Superalloys: Fundamentals and Applications , 2006 .

[37]  Peter D. Lee,et al.  A new mechanism for freckle initiation based on microstructural level simulation , 2012 .

[38]  Adam Morawiec.  A note on mean orientation , 1998 .

[39]  J.-C. Gebelin,et al.  Prediction of recrystallization in investment cast single-crystal superalloys , 2013 .

[40]  M. McLean,et al.  Directionally Solidified Materials for High Temperature Service , 1984 .

[41]  J. Mackenzie,et al.  SECOND PAPER ON STATISTICS ASSOCIATED WITH THE RANDOM DISORIENTATION OF CUBES , 1958 .

[42]  L. Brush,et al.  Observation of Misoriented Tertiary Dendrite Arms During Controlled Directional Solidification in Aluminum-7 Wt pct Silicon Alloys , 2012, Metallurgical and Materials Transactions A.