Numerical simulation for the estimation the jacking force of pipe jacking

Abstract For a pipe jacking construction, reducing the soil–pipe interface friction and providing enough jacking force are the most common approach to optimize the construction efficiency. In practice, jacking force is generally estimated by various empirical equations. However, the estimations of empirical equations frequently deviate from the reality. In this study, a model coupling finite element method and a displacement control method were applied to estimate the required jacking force in pipe jacking. Two cases were examined from Central Taiwan, where the primary geological foundation composed of gravel formations. Case A pertained to pipe jacking construction during which sewage pipes with a diameter of 2.4 m were utilized. The monitoring data from this case were used to establish the jacking force estimation model. The jacking force history observed in Case B, in which sewage pipes of 1.0 m diameter were used, was compared with those obtained by the developed model to demonstrate the applicability of the model. The results suggested the developed model can estimate the jacking force with a better accuracy towards the middle and the final stage of the pipe jacking process.

[1]  Marco Barla,et al.  Analysis of jacking forces during microtunnelling in limestone , 2006 .

[2]  Keh-Jian Shou,et al.  On the Behavior of a Stuck Curved Pipe-jacking , 2011 .

[3]  Robert Stein,et al.  Cojack: A new statics method of computing and controlling pipe jacking , 2007 .

[4]  Albert Hoch,et al.  Calculation of jacking force by new ATV A-161 , 2010 .

[5]  Marco Barla,et al.  A method to design microtunnelling installations in randomly cemented Torino alluvial soil , 2013 .

[6]  Keh-Jian Shou,et al.  On the frictional property of lubricants and its impact on jacking force and soil–pipe interaction of pipe-jacking , 2010 .

[7]  Francesco Borghi,et al.  Soil conditioning for pipe jacking and tunnelling , 2006 .

[8]  Qinxi Dong,et al.  Back analysis of large geotechnical models , 1999 .

[9]  Mostafa Sharifzadeh,et al.  Displacement-based numerical back analysis for estimation of rock mass parameters in Siah Bisheh powerhouse cavern using continuum and discontinuum approach , 2012 .

[10]  Y. Ichioka,et al.  Prediction of jacking forces for microtunnelling operations , 1999 .

[11]  Wout Broere,et al.  Numerical simulation of pile installation , 2011 .

[12]  R Kastner,et al.  Experimental and analytical study of friction forces during microtunneling operations , 2002 .

[13]  Kimberlie Staheli.  Jacking Force Prediction: An Interface Friction Approach based on Pipe Surface Roughness , 2006 .

[14]  Mark Andrew Marshall.  Pipe-jacked tunnelling : jacking loads and ground movements , 1998 .

[15]  Xianjing Kong,et al.  Three-dimensional numerical analysis of the keying of vertically installed plate anchors in clay , 2009 .

[16]  Jamal Rostami,et al.  3D finite difference model for simulation of double shield TBM tunneling in squeezing grounds , 2014 .

[17]  Luqing Zhang,et al.  A displacement-based back-analysis method for rock mass modulus and horizontal in situ stress in tunneling – Illustrated with a case study , 2006 .

[18]  Chun Fai Leung,et al.  Finite element analysis of tunnel–soil–pile interaction using displacement controlled model , 2007 .

[19]  W Wang,et al.  Effect of soil stratification on pipe behaviour due to tunnelling-induced ground movements based on the displacement controlled method , 2012 .

[20]  Hongan Li,et al.  Analysis of jacking force for rectangular pipe-jacking machine , 2012 .

[21]  Wout Broere,et al.  Modelling the boring of curves in (very) soft soils during microtunnelling , 2007 .