Diesel engine dynamometer testing of impedancemetric NOx sensors

Abstract Prototype solid-state electrochemical sensors using a dense gold sensing electrode, porous yttria-stabilized zirconia (YSZ) electrolyte, and a platinum counter electrode (Au/YSZ/Pt) were evaluated for measuring NOx (NO and NO2) in diesel exhaust. Both electrodes were exposed to the test gas (i.e., there was no reference gas for the counter electrode). An impedancemetric method was used for NOx measurements, where the phase angle was used as the response signal. A portion of the tailpipe exhaust from the dynamometer test stand was extracted and fed into a furnace containing the experimental sensor. The prototype sensor was tested along with a commercially available NOx sensor. Simultaneous measurements for NOx, O2, CO2, H2O, CO, and CH4 in a separate feed stream were made using Fourier transform infrared (FTIR) spectroscopy and an oxygen paramagnetic analyzer. The experimental sensor showed very good measurement capability for NO in the range of 25–250 ppm, with a response paralleling that of the FTIR and commercial sensor. The prototype sensor showed better sensitivity to NOx at the lower concentration ranges. O2 is an interferent for the experimental sensor, resulting in decreased sensitivity for measurement of NOx. Methods to overcome this interference are discussed.

[1]  R. Glass,et al.  Impedance Characterization of a Model Au ∕ Yttria -Stabilized Zirconia ∕ Au Electrochemical Cell in Varying Oxygen and NO x Concentrations , 2006 .

[2]  Norio Miura,et al.  Development of zirconia-based potentiometric NOx sensors for automotive and energy industries in the early 21st century : What are the prospects for sensors? , 2007 .

[3]  David James Scholl,et al.  Development of an Al2O3/ZrO2-Composite High-Accuracy NOx Sensor , 2010 .

[4]  Briggs M. White,et al.  Effect of Electrode Microstructure on the Sensitivity and Response Time of Potentiometric NOX Sensors , 2008 .

[5]  Prabir K. Dutta,et al.  High‐Temperature Ceramic Gas Sensors: A Review , 2006 .

[6]  N. Miura,et al.  Electrochemical NOx sensors based on stabilized zirconia: comparison of sensing performances of mixed-potential-type and impedancemetric NOx sensors , 2006 .

[7]  W. Kenan,et al.  Impedance Spectroscopy: Emphasizing Solid Materials and Systems , 1987 .

[8]  Ralf Moos,et al.  Catalysts as Sensors—A Promising Novel Approach in Automotive Exhaust Gas Aftertreatment , 2010, Sensors.

[9]  Robert S. Glass,et al.  Impedancemetric NO x Sensing Using YSZ Electrolyte and YSZ ∕ Cr2O3 Composite Electrodes , 2007 .

[10]  Nianqiang Wu,et al.  Impedance-metric Pt/YSZ/Au–Ga2O3 sensor for CO detection at high temperature , 2005 .

[11]  Noboru Yamazoe,et al.  Toward innovations of gas sensor technology , 2005 .

[12]  Prabir K. Dutta,et al.  High temperature potentiometric NO2 sensor with asymmetric sensing and reference Pt electrodes , 2010 .

[13]  J. Stetter,et al.  Amperometric gas sensors--a review. , 2008, Chemical reviews.

[14]  Maria Luisa Grilli,et al.  Sensing Mechanism of Potentiometric Gas Sensors Based on Stabilized Zirconia with Oxide Electrodes Is It Always Mixed Potential , 2004 .

[15]  Norio Miura,et al.  Development of NOx sensing devices based on YSZ and oxide electrode aiming for monitoring car exhausts , 2004 .

[16]  R. Glass,et al.  Effect of Electrode Material and Design on Sensitivity and Selectivity for High Temperature Impedancemetric NO x Sensors , 2009 .

[17]  Ralf Moos,et al.  A Brief Overview on Automotive Exhaust Gas Sensors Based on Electroceramics , 2005 .

[18]  Claude Lucat,et al.  Critical review of nitrogen monoxide sensors for exhaust gases of lean burn engines , 2000 .

[19]  Jeffrey W. Fergus.  Materials for high temperature electrochemical NOx gas sensors , 2007 .

[20]  Robert F. Novak,et al.  Effect of Electrode Composition and Microstructure on Impedancemetric Nitric Oxide Sensors Based on YSZ Electrolyte , 2007 .