Integrating Two-Stage Phase Change Material Thermal Storage for Cascaded Waste Heat Recovery of Diesel-Engine-Powered Distributed Generation Systems: A Case Study

Thermal energy storage using the latent heat of phase change materials (PCMs) is a promising technique to solve the time mismatch between the availability and usage of flue gas heat in distributed generation systems (DGSs). A diesel-engine-powered DGS integrated with two-stage tube-type PCM modules for exhaust gas heat recovery was developed and studied. Energy and exergy analysis for the PCM storage unit was carried out to verify the effectiveness of the PCM modules for heat recovery and to highlight the merits of the cascaded configuration through a practical engineering case. Furthermore, the performance of the DGS was evaluated to study the contribution of PCM storage to improving system efficiency. The results showed that 56.4% energy and 48.3% exergy of the input flue gas were stored by the two-stage storage unit. Additional integration of the low-temperature PCM module to the high-temperature module improved the average storage efficiency from 33.6% to 62.3% for energy and 33.1% to 50.8% for exergy. By utilizing the stored energy for heating water, the thermal efficiency of the diesel engine was increased from the original 35.8% to 41.9%, while the exergy efficiency was improved from 29.5% to 29.7%.

[1]  D. Buddhi,et al.  Thermal performance assessment of encapsulated PCM based thermal management system to reduce peak energy demand in buildings , 2016 .

[2]  G. Fang,et al.  Thermal energy storage materials and systems for solar energy applications , 2017 .

[3]  Rahman Saidur,et al.  A review on supercooling of Phase Change Materials in thermal energy storage systems , 2017 .

[4]  Ya-Ling He,et al.  Exergy analysis and optimization of charging–discharging processes of latent heat thermal energy storage system with three phase change materials , 2016 .

[5]  Nasiru I. Ibrahim,et al.  A review on current status and challenges of inorganic phase change materials for thermal energy storage systems , 2017 .

[6]  Muhammad M. Rahman,et al.  Comparison between the single-PCM and multi-PCM thermal energy storage design , 2014 .

[7]  Yong Deng,et al.  Expanded graphite for thermal conductivity and reliability enhancement and supercooling decrease of MgCl2⋅6H2O phase change material , 2018, Materials Research Bulletin.

[8]  H. Climent,et al.  Potential of exhaust heat recovery for intake charge heating in a diesel engine transient operation at cold conditions , 2016 .

[9]  Alain Sommier,et al.  Thermal management of electronic devices using carbon foam and PCM/nano-composite , 2015 .

[10]  Tarik Kousksou,et al.  Exergy based performance evaluation of latent heat thermal storage system: A review , 2010 .

[11]  N. M. Al-Najem,et al.  Energy-exergy analysis of a diesel engine , 1992 .

[12]  Ibrahim Dincer,et al.  Thermodynamic Analysis of Freezing and Melting Processes in a Bed of Spherical PCM Capsules , 2009 .

[13]  Yunting Ge,et al.  CFD modelling development and experimental validation of a phase change material (PCM) heat exchanger with spiral-wired tubes , 2018 .

[14]  Dong Li,et al.  Numerical analysis on thermal performance of roof contained PCM of a single residential building , 2015 .

[15]  Ming Jin,et al.  Cascade energy optimization for waste heat recovery in distributed energy systems , 2018, Applied Energy.

[16]  Davood Domiri Ganji,et al.  A review of different heat exchangers designs for increasing the diesel exhaust waste heat recovery , 2014 .

[17]  Gequn Shu,et al.  Experimental investigations on a cascaded steam-/organic-Rankine-cycle (RC/ORC) system for waste heat recovery (WHR) from diesel engine , 2016 .

[18]  Fan Yuan,et al.  Experimental study on thermal performance of high-temperature molten salt cascaded latent heat thermal energy storage system , 2018 .

[19]  Qingsong Wang,et al.  Numerical study on the thermal performance of a composite board in battery thermal management system , 2016 .

[20]  Wasim Saman,et al.  Development and experimental validation of a CFD model for PCM in a vertical triplex tube heat exchanger , 2017 .

[21]  Li Guanghua,et al.  Performance evaluation and experiment system for waste heat recovery of diesel engine , 2013 .

[22]  Mehrdad Boroushaki,et al.  Performance evaluation and optimization of encapsulated cascade PCM thermal storage , 2017 .

[23]  Mehmet Kanoglu,et al.  First and second law analysis of diesel engine powered cogeneration systems , 2008 .

[24]  F. Haghighat,et al.  Air-PCM heat exchanger for peak load management: Experimental and simulation , 2016 .

[25]  Subrata Sengupta,et al.  Effect of porosity of conducting matrix on a phase change energy storage device , 2016 .

[26]  Peng Zhang,et al.  Thermal energy storage and retrieval characteristics of a molten-salt latent heat thermal energy storage system , 2016 .

[27]  S. F. Smeding,et al.  Performance analysis of industrial PCM heat storage lab prototype , 2018, Journal of Energy Storage.

[28]  K. E. Elfeky,et al.  Numerical comparison between single PCM and multi-stage PCM based high temperature thermal energy storage for CSP tower plants , 2018, Applied Thermal Engineering.

[29]  Alparslan Oztekin,et al.  Exergy analysis of cascaded encapsulated phase change material—High-temperature thermal energy storage systems , 2016 .

[30]  Saffa Riffat,et al.  Thermoelectrics: a review of present and potential applications , 2003 .

[31]  Daniel Champier,et al.  Thermoelectric generators: A review of applications , 2017 .

[32]  Luisa F. Cabeza,et al.  Experimental evaluation at pilot plant scale of multiple PCMs (cascaded) vs. single PCM configuration for thermal energy storage , 2015 .

[33]  Huijin Xu,et al.  Thermal performance of cascaded thermal storage with phase-change materials (PCMs). Part I: Steady cases , 2017 .

[34]  R. Velraj,et al.  Experimental investigation on heat recovery from diesel engine exhaust using finned shell and tube heat exchanger and thermal storage system , 2011 .

[35]  Peng Zhang,et al.  Experimental and numerical investigation of a tube-in-tank latent thermal energy storage unit using composite PCM , 2017 .

[36]  Mohamed A. Teamah,et al.  Utilizing the scavenge air cooling in improving the performance of marine diesel engine waste heat recovery systems , 2018 .

[37]  Ram Thakar,et al.  Design of Heat Exchanger for Waste Heat Recovery from Exhaust Gas of Diesel Engine , 2018 .