Design and fabrication of silicon condenser microphone using corrugated diaphragm technique

A novel silicon condenser microphone with a corrugated diaphragm has been proposed, designed, fabricated and tested. The microphone is fabricated on a single wafer by use of silicon anisotropic etching and sacrificial layer etching techniques, so that no bonding techniques are required. The introduction of corrugations has greatly increased the mechanical sensitivities of the microphone diaphragms due to the reduction of the initial stress in the thin films, For the purpose of further decreasing the thin film stress, composite diaphragms consisting of multilayer (polySi/Si/sub x/N/sub y//polySi) materials have been fabricated, reducing the initial stress to a much lower level of about 70 MPa in tension. Three types of corrugation placements and several corrugation depths in a diaphragm area of 1 mm/sup 2/ have been designed and fabricated. Microphones with flat frequency response between 100 Hz and 8/spl sim/16 kHz and open-circuit sensitivities as high as 8.1/spl sim/14.2 mV/Pa under the bias voltages of 10/spl sim/25 V have been fabricated in a reproducible way. The experimental results proved that the corrugation technique is promising for silicon condenser microphone.

[1]  Miko Elwenspoek,et al.  On-chip decoupling zone for package-stress reduction , 1991 .

[2]  W. Kühnel,et al.  Micromachined subminiature condenser microphones in silicon , 1992 .

[3]  Wouter Olthuis,et al.  The design, fabrication, and testing of corrugated silicon nitride diaphragms , 1994 .

[4]  J. Bergqvist,et al.  A silicon condenser microphone using bond and etch-back technology , 1994 .

[5]  T. Bourouina,et al.  A new condenser microphone with a p+ silicon membrane , 1992 .

[6]  J. Bergqvist,et al.  Capacitive microphone with a surface micromachined backplate using electroplating technology , 1994 .

[7]  Richard S. Muller,et al.  Improved IC-compatible piezoelectric microphone and CMOS process , 1991, TRANSDUCERS '91: 1991 International Conference on Solid-State Sensors and Actuators. Digest of Technical Papers.

[8]  Wouter Olthuis,et al.  Fabrication of silicon condenser microphones using single wafer technology , 1992 .

[9]  Wouter Olthuis,et al.  Improvement of the performance of microphones with a silicon nitride diaphragm and backplate , 1994 .

[10]  A. J. Sprenkels,et al.  Development of an electret microphone in silicon , 1989 .

[11]  P. Murphy,et al.  Subminiature silicon integrated electret capacitor microphone , 1989 .

[12]  Reinoud F. Wolffenbuttel,et al.  Comparison of techniques for measuring both compressive and tensile stress in thin films , 1993 .

[13]  M. Royer,et al.  ZnO on Si integrated acoustic sensor , 1983 .

[14]  J. Bergqvist,et al.  A new condenser microphone in silicon , 1990 .

[15]  Khalil Najafi,et al.  Internal stress compensation and scaling in ultrasensitive silicon pressure sensors , 1992 .

[16]  K. Wise,et al.  Performance of nonplanar silicon diaphragms under large deflections , 1994 .

[17]  R. Schellin,et al.  A silicon subminiature microphone based on piezoresistive polysilicon strain gauges , 1992 .

[18]  E. Graf,et al.  Silicon membrane condenser microphone with integrated field-effect transistor , 1993 .

[19]  A. W. Mitchell,et al.  Fabrication Of A Silicon Micromachined Capacitive Microphone Using A Dry-etch Process , 1995, Proceedings of the International Solid-State Sensors and Actuators Conference - TRANSDUCERS '95.

[20]  Gisela Hess,et al.  A subminiature condenser microphone with silicon nitride membrane and silicon back plate , 1989 .