Effect of fixation stitches on out-of-plane response of textile non-crimp fabric composites

Non-crimp fabrics are fabric tapes stitched to an adjacent orthogonal fabric with no associated crimp. In the current research, the effect of fixation polyester stitches in improving through-the-thickness properties of non-crimp fabric composite laminates is investigated. Detailed experimental studies on interlaminar fracture toughness and static indentation properties of stitched and unstitched thin ply carbon fibre epoxy composites have been conducted. About 23% higher peak load and 37% higher energy absorption were noticed during static indentation tests for the stitched ply composites. A detailed SEM investigation has shown that the stitch-stitch interaction ‘within a bi-angle ply’ and ‘between the bi-angle ply’ plays a significant role in reducing the delamination extent. The critical energy release rate during Mode I fracture toughness of stitched composites was found to be 26.5% higher and SEM investigation depicted that the stitches promote the intra-laminar delamination and enhance the toughness of the composite.

[1]  Y. Mai,et al.  The effect of stitch distribution on mode I delamination toughness of stitched laminated composites – experimental results and FEA simulation , 2007 .

[2]  T. Gries,et al.  Geometrical and mechanical properties of a non-crimp fabric applicable for textile reinforced concrete , 2014 .

[3]  Albertino José Castanho Arteiro,et al.  Technology development and structural mechanics of composites built of spread tow thin-ply technology , 2012 .

[4]  Y. Mai,et al.  On the effects of stitching in CFRPs—II. Mode II delamination toughness , 1998 .

[5]  S. Joshi,et al.  Experimental investigation on suitability of carbon fibre thin plies for racquets , 2016 .

[6]  N. Himmel,et al.  Structurally stitched NCF CFRP laminates. Part 1: Experimental characterization of in-plane and out-of-plane properties , 2011 .

[7]  H. Hess,et al.  Mechanical properties of structurally stitched non-crimp fabric composites , 2011 .

[8]  T. Ishikawa,et al.  Understanding effectiveness of stitching in suppression of impact damage: An empirical delamination reduction trend for stitched composites , 2012 .

[9]  P. Hogg,et al.  The mechanical properties of non-crimped fabric-based composites , 1993 .

[10]  M. E. Üreyen,et al.  Determination of silver release from antibacterial finished cotton and polyester fabrics into water , 2016 .

[11]  Y. Mai,et al.  Effect of stitching on interlaminar delamination extension in composite laminates , 1993 .

[12]  S. Joshi,et al.  Enhanced vibration damping and dynamic mechanical characteristics of composites with novel pseudo-thermoset matrix system , 2017 .

[13]  Mateusz Koziol,et al.  Experimental study on the effect of stitch arrangement on mechanical performance of GFRP laminates manufactured on a basis of stitched preforms , 2012 .

[14]  I. Verpoest,et al.  Mechanical properties of non-crimp fabric (NCF) based composites: stiffness and strength , 2011 .

[15]  P. Mitschang,et al.  Structural stitching of non-crimp fabric preforms for composites , 2011 .

[16]  G. Tsai,et al.  Effect of stitching on mode i strain energy release rate , 2005 .

[17]  P. Camanho,et al.  Notched response of non-crimp fabric thin-ply laminates , 2013 .

[18]  Emile S. Greenhalgh,et al.  Failure Analysis and Fractography of Polymer Composites , 2009 .

[19]  Sunil C. Joshi,et al.  Microwave–thermal technique for energy and time efficient curing of carbon fiber reinforced polymer prepreg composites , 2014 .

[20]  S. Joshi,et al.  Mechanical and vibration response of insulated hybrid composites , 2018 .

[21]  S. Joshi,et al.  Mode I fracture toughness and fractographic investigation of carbon fibre composites with liquid Methylmethacrylate thermoplastic matrix , 2018 .

[22]  V. Altstädt,et al.  Mechanical performance of carbon fibre-reinforced composites based on preforms stitched with innovative low-melting temperature and matrix soluble thermoplastic yarns , 2008 .

[23]  B. Cina,et al.  Fractography of multidirectional CFRP composites tested statically , 1991 .

[24]  Sergio Oller,et al.  Numerical simulation of fiber reinforced composite materials––two procedures , 2002 .

[25]  Vishwesh Dikshit,et al.  Multiscale Polymer Composites: A Review of the Interlaminar Fracture Toughness Improvement , 2017 .

[26]  S. Tsai,et al.  Experimental studies of thin-ply laminated composites , 2007 .

[27]  Tae Jin Kang,et al.  Effect of Stitching on the Mechanical and Impact Properties of Woven Laminate Composite , 1994 .

[28]  W. Bascom,et al.  Fractography of the interlaminar fracture of carbon-fibre epoxy composites , 1985 .

[29]  S. Joshi,et al.  Design, Manufacturing and Testing of Filament Wound Composite Risers for Marine and Offshore Applications , 2015 .

[30]  Yiu-Wing Mai,et al.  Effect of stitch distribution on mode I delamination toughness of laminated DCB specimens , 2004 .

[31]  N. Watanabe,et al.  Effect of stitch density and stitch thread thickness on low-velocity impact damage of stitched composites , 2010 .

[32]  L. K. Jain,et al.  ON THE EFFECT OF STITCHING ON MODE I DELAMINATION TOUGHNESS OF LAMINATED COMPOSITES , 1994 .

[33]  S. Joshi,et al.  Optimizing Polymer Infusion Process for Thin Ply Textile Composites with Novel Matrix System , 2017, Materials.

[34]  M. Umair,et al.  Investigation of mechanical behavior of woven/knitted hybrid composites , 2017 .

[35]  Kristopher P. Plain,et al.  The effect of stitch incline angle on mode I fracture toughness – Experimental and modelling , 2010 .

[36]  Barry T. Smith,et al.  Compression Response of Thick Layer Composite Laminates with Through-the-Thickness Reinforcement , 1992 .