CMP of hard disk substrate using a colloidal SiO2 slurry: preliminary experimental investigation

[1]  J. Warnock,et al.  A two-dimensional process model for chemimechanical polish planarization , 1991 .

[2]  I. Ali,et al.  Chemical-mechanical polishing of interlayer dielectric: a review , 1994 .

[3]  B. Bhushan,et al.  Surface roughness analysis of glass-ceramic substrates and finished magnetic disks, and Ni-P coated Al-Mg and glass substrates , 1995 .

[4]  Farid Malik,et al.  Manufacturability of the CMP process , 1995 .

[5]  B. Bhushan,et al.  Nanoindentation, microscratch, friction and wear studies of coatings for contact recording applications , 1995 .

[6]  G. Nanz,et al.  Modeling of chemical-mechanical polishing: a review , 1995 .

[7]  B. Bhushan,et al.  Effects of particle size, polishing pad and contact pressure in free abrasive polishing , 1996 .

[8]  M. Pohl,et al.  The Importance of Particle Size to the Performance of Abrasive Particles in the CMP Process , 1996 .

[9]  B. Bhushan,et al.  Wear and friction studies of contact recording interface with microfabricated heads , 1996 .

[10]  Ronald J. Gutmann,et al.  Chemical Mechanical Planarization of Microelectronic Materials , 1997 .

[11]  Hong Liang,et al.  Wear phenomena in chemical mechanical polishing , 1997 .

[12]  Hong Liang,et al.  Effect of slurry viscosity modification on oxide and tungsten CMP , 1998 .

[13]  J. Larsen-Basse,et al.  Probable role of abrasion in chemo-mechanical polishing of tungsten , 1999 .

[14]  B. Bhushan.  Chemical, mechanical and tribological characterization of ultra-thin and hard amorphous carbon coatings as thin as 3.5 nm: recent developments , 1999 .

[15]  David J. Stein,et al.  Investigation of the Kinetics of Tungsten Chemical Mechanical Polishing in Potassium Iodate‐Based Slurries: I. Role of Alumina and Potassium lodate , 1999 .

[16]  Ultra-thin tetrahedral amorphous carbon film as slider overcoat for high areal density magnetic recording , 1999 .

[17]  Uday Mahajan,et al.  Effect of Particle Size during Tungsten Chemical Mechanical Polishing , 1999 .

[18]  Sang-Shin Park,et al.  Hydrodynamic analysis of chemical mechanical polishing process , 2000 .

[19]  B. Moudgil,et al.  Effect of Particle Size of Chemical Mechanical Polishing Slurries for Enhanced Polishing with Minimal Defects , 2000 .

[20]  Studies of fly stiction , 2001 .

[21]  Sang-Shin Park,et al.  Three-dimensional wafer scale hydrodynamic modeling for chemical mechanical polishing , 2001 .

[22]  David Dornfeld,et al.  Material removal mechanism in chemical mechanical polishing: theory and modeling , 2001 .

[23]  Yongwu Zhao,et al.  A micro-contact and wear model for chemical-mechanical polishing of silicon wafers , 2002 .

[24]  Hong Liang,et al.  Lubricating behavior in chemical–mechanical polishing of copper , 2002 .

[25]  Chunhong Zhou,et al.  Influence of Colloidal Abrasive Size on Material Removal Rate and Surface Finish in SiO2 Chemical Mechanical Polishing , 2002 .

[26]  Chemical Mechanical Polishing of Computer Hard Disk Substrate in Colloidal SiO2 Slurry , 2002 .

[27]  S. Danyluk,et al.  Fluid pressure and its effects on chemical mechanical polishing , 2002 .

[28]  The Removal Selectivity of Titanium and Aluminum in Chemical Mechanical Planarization , 2002 .

[29]  Seong H. Kim,et al.  A mathematical model for chemical–mechanical polishing based on formation and removal of weakly bonded molecular species , 2003 .

[30]  Fang Wang,et al.  Investigation on the final polishing slurry and technique of silicon substrate in ULSI , 2003 .

[31]  A. Nakajima,et al.  Possibility of surface force effect in slider air bearings of 100 Gbit/in2 hard disks , 2003 .

[32]  Junguo Xu,et al.  Ultra-Low-Flying-Height Design from the Viewpoint of Contact Vibration , 2003 .

[33]  T. Cale,et al.  Multiscale material removal modeling of chemical mechanical polishing , 2003 .