A circular membrane for nano thin film micro solid oxide fuel cells with enhanced mechanical stability

We demonstrate a new architecture for a low temperature solid oxide fuel cell to enlarge the lateral dimension of the fragile nano thin film electrolyte from the micrometer to millimeter scale with greatly enhanced mechanical stability. The new structure was achieved by simple silicon micromachining processes to change the membrane shape from a square to a circle to reduce buckling-induced stress concentration that often caused membrane fracture. A tapered silicon membrane support with the thickest end of 30 μm was introduced as an effective membrane stress absorber. The new architecture effectively suppressed membrane buckling and decreased the maximum principal stress by 30–40%. The largest lateral dimension of the stable membranes was 3 mm in diameter, and the survival rate was significantly improved over square membranes having the same lateral dimension. Fuel cells with 100 nm-thick electrolytes showed stable open circuit voltages of 1.12 V at 400 °C for more than 8 hours without any membrane failure observed, showing the superior mechanical stability of the new cell architecture that is promising in the further practical applications of such devices.

[1]  D. Lincot,et al.  Yttria-doped zirconia thin films deposited by atomic layer deposition ALD: a structural, morphological and electrical characterisation , 2003 .

[2]  V. T. Srikar,et al.  Structural design considerations for micromachined solid oxide fuel cells , 2004 .

[3]  Jiujun Zhang,et al.  Design consideration of micro thin film solid-oxide fuel cells , 2005 .

[4]  Fritz B. Prinz,et al.  High-Performance Ultrathin Solid Oxide Fuel Cells for Low-Temperature Operation , 2007 .

[5]  Fritz B. Prinz,et al.  Atomic layer deposition of yttria-stabilized zirconia for solid oxide fuel cells , 2007 .

[6]  L. Gauckler,et al.  Thin films for micro solid oxide fuel cells , 2007 .

[7]  L. Gauckler,et al.  Micro Solid Oxide Fuel Cells on Glass Ceramic Substrates , 2008 .

[8]  F. Prinz,et al.  Solid oxide fuel cell with corrugated thin film electrolyte. , 2008, Nano letters.

[9]  S. Spearing,et al.  Residual stress and microstructure of as-deposited and annealed, sputtered yttria-stabilized zirconia thin films , 2008 .

[10]  P. Muralt,et al.  Solid oxide fuel cell membranes supported by nickel grid anode , 2008 .

[11]  Bo-Kuai Lai,et al.  Microstructure and Microfabrication Considerations for Self‐Supported On‐Chip Ultra‐Thin Micro‐Solid Oxide Fuel Cell Membranes , 2009 .

[12]  M. Ferraris,et al.  Yttria-stabilized zirconia thin film electrolyte produced by RF sputtering for solid oxide fuel cell applications , 2010 .

[13]  M. Döbeli,et al.  Yttria-stabilized zirconia thin films by pulsed laser deposition: Microstructural and compositional control , 2010 .

[14]  S. Ramanathan,et al.  On the role of ultra-thin oxide cathode synthesis on the functionality of micro-solid oxide fuel cells: Structure, stress engineering and in situ observation of fuel cell membranes during operation , 2010 .

[15]  Emiliana Fabbri,et al.  High proton conduction in grain-boundary-free yttrium-doped barium zirconate films grown by pulsed laser deposition. , 2010, Nature materials.

[16]  Ki-Bum Kim,et al.  High‐Performance Micro‐Solid Oxide Fuel Cells Fabricated on Nanoporous Anodic Aluminum Oxide Templates , 2011 .

[17]  S. Ramanathan,et al.  Pt/Y0.16Zr0.84O1.92/Pt thin film solid oxide fuel cells: Electrode microstructure and stability considerations , 2011 .

[18]  F. Prinz,et al.  Cup-shaped yttria-doped barium zirconate membrane fuel cell array , 2011 .

[19]  S. Ramanathan,et al.  Low temperature thin film solid oxide fuel cells with nanoporous ruthenium anodes for direct methane operation , 2011 .

[20]  P. Muralt,et al.  Experimental study of single triple-phase-boundary and platinum-yttria stabilized zirconia composite as cathodes for micro-solid oxide fuel cells , 2012 .

[21]  S. Ramanathan,et al.  Free standing oxide alloy electrolytes for low temperature thin film solid oxide fuel cells , 2012 .

[22]  L. Gauckler,et al.  Processing of Foturan® glass ceramic substrates for micro-solid oxide fuel cells , 2012 .

[23]  S. Ramanathan,et al.  Ultra-thin film solid oxide fuel cells utilizing un-doped nanostructured zirconia electrolytes , 2012 .

[24]  N. D. de Rooij,et al.  Residual Stress and Buckling Patterns of Free‐standing Yttria‐stabilized‐zirconia Membranes Fabricated by Pulsed Laser Deposition , 2012 .

[25]  S. Uhlenbruck,et al.  Dense yttria-stabilised zirconia electrolyte layers for SOFC by reactive magnetron sputtering , 2012 .

[26]  F. Prinz,et al.  Nanoscale membrane electrolyte array for solid oxide fuel cells , 2012 .

[27]  P. Su,et al.  Combinatorial deposition of a dense nano-thin film YSZ electrolyte for low temperature solid oxide fuel cells , 2013 .

[28]  Gaetano Chiodelli,et al.  Electrochemical open circuit voltage (OCV) characterization of SOFC materials , 2013, Ionics.

[29]  L. Mahadevan,et al.  Elastic configurations of self-supported oxide membranes for fuel cells , 2013 .

[30]  Suk Won Cha,et al.  Atomic layer deposition of thin-film ceramic electrolytes for high-performance fuel cells , 2013 .

[31]  S. Ramanathan,et al.  Free standing yttria-doped zirconia membranes: Geometrical effects on stability , 2015, Journal of Electroceramics.

[32]  Luis Fonseca,et al.  Full ceramic micro solid oxide fuel cells: towards more reliable MEMS power generators operating at high temperatures , 2014 .

[33]  P. Su,et al.  Chemical stability study of nanoscale thin film yttria-doped barium cerate electrolyte for micro solid oxide fuel cells , 2014 .

[34]  Suk Won Cha,et al.  Plasma-enhanced atomic layer deposition of nanoscale yttria-stabilized zirconia electrolyte for solid oxide fuel cells with porous substrate. , 2015, ACS applied materials & interfaces.