Influence of phase position on the chemical response of oscillator driven polymer coated SAW resonators

The use of oscillator operated SAW resonators as chemical sensors is widely accepted to have the best sensing properties. However, some important parameters of influence are not sufficient resolved, yet. In general, these are effects arising from the electronic circuitry such as the phase situation on the chemical response of these sensors. We have found that they can be almost dramatic for several types of sensitive coatings and, thus, are not negligible, especially their influence on the sensitivity. In this work some exemplary results with SAW resonators working at 433,92 MHz coated with different polymeric films such as polyisobutylene (PIB), polyepichlorohydrine (PECH) or polydimethylsiloxane (PDMS) and sampled with toluene as analyte. Depending on thickness and homogeneity of the polymer film serious influences of the set phase positions on the quality of the chemical response were observed such as curve shape, and signal to noise ratio. Also, a simulation using an equivalent circuit model of the transducers including the polymer coating is used for a deeper understanding of these phenomena.

[1]  H. Gemmeke,et al.  Development of an analytical microsystem for organic gas detection based on surface acoustic wave resonators , 1995 .

[2]  Jay W. Grate,et al.  Method for Estimating Polymer-Coated Acoustic Wave Vapor Sensor Responses , 1995 .

[3]  Michael Thompson,et al.  Interdigital capacitance and surface acoustic wave sensors , 1993 .

[4]  R. A. McGill,et al.  Determination of partition coefficients from surface acoustic wave vapor sensor responses and correlation with gas-liquid chromatographic partition coefficients , 1988 .

[5]  G. Hayward,et al.  Mass response of the thickness-shear mode acoustic wave sensor in liquids as a central misleading dogma , 1997, Proceedings of International Frequency Control Symposium.

[6]  E. Zellers,et al.  Optimal coating selection for the analysis of organic vapor mixtures with polymer-coated surface acoustic wave sensor arrays. , 1995, Analytical chemistry.

[7]  J. Reibel,et al.  SAGAS: gas analyzing sensor systems based on surface acoustic wave devices-an issue of commercialization of SAW sensor technology , 1997, Proceedings of International Frequency Control Symposium.

[8]  Jay W. Grate,et al.  Examination of mass and modulus contributions to thickness shear mode and surface acoustic wave vapour sensor responses using partition coefficients , 1997 .

[9]  H. Wohltjen.  Mechanism of Operation and Design Considerations for Surface Acoustic Wave Device Vapor Sensors. , 1984 .

[10]  R. A. McGill,et al.  CHOOSING POLYMER COATINGS FOR CHEMICAL SENSORS , 1994 .

[11]  Nathali Kaushansky,et al.  The polymer-coated SAW sensor as a gravimetric sensor , 1997 .

[12]  Raymond E. Dessy,et al.  Surface acoustic wave probe for chemical analysis. I. Introduction and instrument description , 1979 .

[13]  R. Müller,et al.  Multidimensional sensor for gas analysis , 1986 .

[14]  J. Grate,et al.  Comparisons of polymer/gas partition coefficients calculated from responses of thickness shear mode and surface acoustic wave vapor sensors. , 1998, Analytical chemistry.

[15]  R. A. McGill,et al.  The predominant role of swelling-induced modulus changes of the sorbent phase in determining the responses of polymer-coated surface acoustic wave vapor sensors , 1992 .

[16]  Stephen J. Martin,et al.  Dynamics and Response of Polymer-Coated Surface Acoustic Wave Devices: Effect of Viscoelastic Properties and Film Resonance , 1994 .

[17]  G. C. Frye,et al.  Surface acoustic wave response to changes in viscoelastic film properties , 1990 .

[18]  Franz L. Dickert,et al.  SAW and QMB for chemical sensing , 1997, Proceedings of International Frequency Control Symposium.

[19]  R. A. McGill,et al.  Fullerene as an adsorbent for gases and vapours , 1993 .

[20]  H. Fuchs,et al.  A new high-frequency high-sensitivity SAW device for NO2 gas detection in the sub-ppm range , 1991 .