Effect of ethanol on the formation and properties of a Cu-NbC composite

Abstract Copper (Cu), niobium (Nb) and graphite (C) powders were used as starting materials to produce an in-situ Cu–15 vol% NbC composite using mechanical alloying followed by spark plasma sintering (SPS). A mixture of Cu, Nb and C powders was milled in an argon atmosphere for 30 h. Different amounts of ethanol were used to study the effect of the process control agent on the formation of NbC and the consequent properties of the Cu–NbC composite. The results showed that NbC was formed in the copper matrix during ball milling when the powders were milled with 0–2 wt% ethanol, whilst the powder milled with 5 wt% ethanol only exhibited NbC formation after sintering. The as-milled powders were then sintered using SPS at 1000 °C, an applied pressure of 100 MPa and soaking duration of 15 min. As a result, the best combination of properties was observed in the sintered Cu–15 vol% NbC composite using a powder milled with 1 wt% ethanol, viz. electrical conductivity of 24% IACS, microhardness of 377 Hv and relative density of 97%.

[1]  A. Ataie,et al.  Structural investigation on nano-crystalline Cu–Cr supersaturated solid solution prepared by mechanical alloying , 2010 .

[2]  N. Parvin,et al.  Characterization and formation mechanism of nanocrystalline W–Al alloy prepared by mechanical alloying , 2010 .

[3]  Frederick L. Dryer,et al.  Experimental and Numerical Studies of Ethanol Decomposition Reactions , 2004 .

[4]  C. Melandri,et al.  Microstructure and mechanical properties of an HfB2 + 30 vol.% SiC composite consolidated by spark plasma sintering , 2006 .

[5]  J. Suñol,et al.  The effects of process control agents on mechanical alloying behavior of a Fe–Zr based alloy , 2007 .

[6]  F. Turquier,et al.  Single-phase bulk Al–Cu–Fe quasicrystals by field-assisted sintering , 2008 .

[7]  J. K. Lee,et al.  Preparation of TiB2 powders by mechanical alloying , 2002 .

[8]  M. Leparoux,et al.  Investigation of planetary milling for nano-silicon carbide reinforced aluminium metal matrix composites , 2010 .

[9]  Mansour Razavi,et al.  Production of Al–20 wt.% Al2O3 composite powder using high energy milling , 2009 .

[10]  M. Umemoto,et al.  Synthesis of copper–niobium carbide composite powder by in situ processing , 2008 .

[11]  J. B. Correia,et al.  XRD, XPS and SEM characterisation of Cu-NbC nanocomposite produced by mechanical alloying , 2008 .

[12]  M. Omori.  Sintering, consolidation, reaction and crystal growth by the spark plasma system (SPS) , 2000 .

[13]  S. J. Askari,et al.  Microstructure, mechanical properties, electrical conductivity and wear behavior of high volume TiC reinforced Cu-matrix composites , 2009 .

[14]  Li Lu,et al.  Influence of process control agent on interdiffusion between Al and Mg during mechanical alloying , 1999 .

[15]  B. S. Murty,et al.  Al-(L12)Al3Ti nanocomposites prepared by mechanical alloying: Synthesis and mechanical properties , 2010 .

[16]  Li Lu,et al.  Prediction of the amount of PCA for mechanical milling , 1999 .

[17]  J. Kuebler,et al.  Microstructure and electrical properties of Si3N4-TiN composites sintered by hot pressing and spark plasma sintering , 2007 .

[18]  Z. Cao,et al.  Fabrication of the supersaturated solid solution of carbon in copper by mechanical alloying , 2007 .

[19]  H. Zuhailawati,et al.  Effects of milling time on hardness and electrical conductivity of in situ Cu-NbC composite produced by mechanical alloying , 2009 .

[20]  M. Miki-Yoshida,et al.  Graphite nanoparticle dispersion in 7075 aluminum alloy by means of mechanical alloying , 2009 .

[21]  C. Suryanarayana,et al.  Mechanical alloying and milling , 2004 .

[22]  D. Božić,et al.  Characterization of prealloyed copper powders treated in high energy ball mill , 2006 .