Optimization of varying-parameter drilling for multi-hole parts using metaheuristic algorithm coupled with self-adaptive penalty method

[1]  S. Kaldor,et al.  Investigation in Tool Life of Twist Drills , 1980 .

[2]  Etsuo Marui,et al.  Whirling Vibration in Drilling. Part 1: Cause of Vibration and Role of Chisel Edge , 1986 .

[3]  J. Deng,et al.  Introduction to Grey system theory , 1989 .

[4]  Jun Ni,et al.  Analysis of drill failure modes by multi-sensors on a robotic end effector , 1996 .

[5]  Ranga Komanduri,et al.  Frequency and time domain analyses of sensor signals in drilling. I: Correlation with drill wear , 1995 .

[6]  Y. S. Tarng,et al.  Modeling and optimization of drilling process , 1998 .

[7]  Y. S. Tarng,et al.  In-process prediction of corner wear in drilling operations , 2000 .

[8]  R. Eberhart,et al.  Comparing inertia weights and constriction factors in particle swarm optimization , 2000, Proceedings of the 2000 Congress on Evolutionary Computation. CEC00 (Cat. No.00TH8512).

[9]  Kenneth A. Loparo,et al.  Tool wear condition monitoring in drilling operations using hidden Markov models (HMMs) , 2001 .

[10]  Issam Abu-Mahfouz,et al.  Drilling wear detection and classification using vibration signals and artificial neural network , 2003 .

[11]  Jun Ni,et al.  Continuous chip formation in drilling , 2005 .

[12]  David N. Dilley,et al.  Effects of the chisel edge on the chatter frequency in drilling , 2005 .

[13]  N Tosun,et al.  Determination of optimum parameters for multi-performance characteristics in drilling by using grey relational analysis , 2006 .

[14]  Hong Hocheng,et al.  Evaluation of thrust force and surface roughness in drilling composite material using Taguchi analysis and neural network , 2008 .

[15]  Keith Ridgway,et al.  Tool life and surface integrity aspects when drilling and hole making in Inconel 718 , 2008 .

[16]  Gary G. Yen,et al.  Constraint Handling in Multiobjective Evolutionary Optimization , 2009, IEEE Transactions on Evolutionary Computation.

[17]  P. Withers,et al.  The sensitivity of Ni-based superalloy to hole making operations: Influence of process parameters on subsurface damage and residual stress , 2009 .

[18]  Yusuf Kaynak,et al.  Application of Taguchi methods in the optimization of cutting parameters for surface finish and hole diameter accuracy in dry drilling processes , 2009 .

[19]  P. Withers,et al.  Minor cutting edge-workpiece interactions in drilling of an advanced nickel-based superalloy , 2009 .

[20]  Ahmet Yardimeden,et al.  Optimization of drilling parameters on surface roughness in drilling of AISI 1045 using response surface methodology and genetic algorithm , 2011 .

[21]  Adem Çiçek,et al.  Taguchi method based optimisation of drilling parameters in drilling of AISI 316 steel with PVD monolayer and multilayer coated HSS drills , 2012 .

[22]  V. N. Gaitonde,et al.  Minimizing burr size in drilling using artificial neural network (ANN)-particle swarm optimization (PSO) approach , 2012, J. Intell. Manuf..

[23]  M. Saravanan,et al.  Multi Objective Optimization of Drilling Parameters Using Genetic Algorithm , 2012 .

[24]  M. Fu,et al.  Hot deformation behavior of GH4169 superalloy associated with stick δ phase dissolution during isothermal compression process , 2012 .

[25]  Inderdeep Singh,et al.  Multi objective optimization in drilling of Al6063/10% SiC metal matrix composite based on grey relational analysis , 2013 .

[26]  Yuebin Guo,et al.  Effect Tool Wear During End Milling on the Surface Integrity and Fatigue Life of Inconel 718 , 2014 .

[27]  B. Suresh Kumar,et al.  Application of Artificial Neural Network Modeling for Machining Parameters Optimization in Drilling Operation , 2014 .

[28]  Dinghua Zhang,et al.  Localization of freeform surface workpiece with particle swarm optimization algorithm , 2014, Proceedings of the 2014 International Conference on Innovative Design and Manufacturing (ICIDM).

[29]  R. Sreenivasulu.  Optimization of Burr size, Surface Roughness and Circularity Deviation during Drilling of Al 6061 using Taguchi Design Method and Artificial Neural Network , 2015 .

[30]  F. Meng,et al.  Surface integrity of GH4169 affected by cantilever finish grinding and the application in aero-engine blades , 2015 .

[31]  Bhargab Kalita.  A Review on Optimization of Cutting Parameters in Drilling using Taguchi Method , 2015 .

[32]  Jianfei Sun,et al.  Effect of Machining Parameters on Surface Integrity in High Speed Milling of Super Alloy GH4169/Inconel 718 , 2016 .

[33]  Junxue Ren,et al.  Multi-objective optimization of multi-axis ball-end milling Inconel 718 via grey relational analysis coupled with RBF neural network and PSO algorithm , 2017 .

[34]  Lihui Wang,et al.  A Novel Approach of Tool Wear Evaluation , 2017 .

[35]  Dinghua Zhang,et al.  Improving tool life in multi-axis milling of Ni-based superalloy with ball-end cutter based on the active cutting edge shift strategy , 2018 .

[36]  R. Vinayagamoorthy,et al.  A central composite design based fuzzy logic for optimization of drilling parameters on natural fiber reinforced composite , 2018 .

[37]  Dinghua Zhang,et al.  Iterative Learning Method for Drilling Depth Optimization in Peck Deep-Hole Drilling , 2018, Journal of Manufacturing Science and Engineering.

[38]  Dinghua Zhang,et al.  Chip evacuation force modelling for deep hole drilling with twist drills , 2018, The International Journal of Advanced Manufacturing Technology.

[39]  N. Arunkumar,et al.  Parametric optimization of deep-hole drilling on AISI 1045 steel and online tool condition monitoring using an accelerometer , 2018 .

[40]  M. Balaji,et al.  Optimization of drilling parameters for drilling of TI-6Al-4V based on surface roughness, flank wear and drill vibration , 2018 .

[41]  Hafiz M. Hafeez,et al.  Four-axis trochoidal toolpath planning for rough milling of aero-engine blisks , 2019, Chinese Journal of Aeronautics.

[42]  Dinghua Zhang,et al.  Mechanistic modelling of worn drill cutting forces with drill wear effect coefficients , 2019, Procedia CIRP.