Fundamental Improvement of Creep Resistance of New-Generation Nano-Oxide Strengthened Alloys via Hot Rotary Swaging Consolidation

New-generation oxide dispersion-strengthened (ODS) alloys with a high volume fraction of nano-oxides of 5% are intended to become the leading creep- and oxidation-resistant alloys for applications at 1100–1300 °C. Hot consolidation of mechanically alloyed powders by intensive plastic deformation followed by heat treatment of the alloys are the key aspects for achieving top creep properties, typically ensured by a coarse-grained microstructure strengthened with homogeneously dispersed, very stable yttrium nano-oxides. The rotary swaging method proves to be favourable for hot consolidation of the new-generation ODS alloy presented. Compared to specimens consolidated by hot rolling, consolidation by hot rotary swaging predetermines the formation of coarse grains with a very high aspect ratio during subsequent secondary recrystallization. Such a grain morphology increases the creep strength of the new-generation ODS alloy considerably.

[1]  J. Svoboda,et al.  The Influence of Aluminum Content on Oxidation Resistance of New-Generation ODS Alloy at 1200 °C , 2020, Metals.

[2]  J. Svoboda,et al.  Influence of Hot Consolidation Conditions and Cr-Alloying on Microstructure and Creep in New-Generation ODS Alloy at 1100 °C , 2020, Materials.

[3]  Lingling Tang,et al.  Bulk nanocrystalline high-strength magnesium alloys prepared via rotary swaging , 2020 .

[4]  H. Riedel,et al.  Modelling of Processing Steps of New Generation ODS Alloys , 2020, Metallurgical and Materials Transactions A.

[5]  N. Lavery,et al.  Effect of thermomechanical processing via rotary swaging on properties and residual stress within tungsten heavy alloy , 2020 .

[6]  C. Schenck,et al.  Material Improvement of Mild Steel S355J2C by Hot Rotary Swaging , 2020 .

[7]  M. Auger,et al.  Nanoscale analysis of ion irradiated ODS 14YWT ferritic alloy , 2020 .

[8]  M. Hermans,et al.  Effect of mechanical alloying and spark plasma sintering on the microstructure and mechanical properties of ODS Eurofer , 2019, Materials & Design.

[9]  Haodong Jia,et al.  The effect of thermal-aging on the microstructure and mechanical properties of 9Cr ferritic/martensitic ODS alloy , 2019, Journal of Nuclear Materials.

[10]  Ying Yang,et al.  Microstructure evolution and mechanical properties of ODS FeCrAl alloys fabricated by an internal oxidation process , 2019, Materials Science and Engineering: A.

[11]  Sen Yu,et al.  Effect of Hot Rotary Swaging and Subsequent Annealing on Microstructure and Mechanical Properties of Magnesium Alloy WE43 , 2019, Metal Science and Heat Treatment.

[12]  K. Dvořák,et al.  Rotary swaged laminated Cu-Al composites: Effect of structure on residual stress and mechanical and electric properties , 2019, Materials Science and Engineering: A.

[13]  S. Schmauder,et al.  Enhanced strength and high temperature resistance of 25Cr20Ni ODS austenitic alloy through thermo-mechanical treatment and addition of Mo , 2019, Fusion Engineering and Design.

[14]  J. Svoboda,et al.  Microstructure Evolution in ODS Alloys with a High-Volume Fraction of Nano Oxides , 2018, Metals.

[15]  P. Král,et al.  Characterization of innovative rotary swaged Cu-Al clad composite wire conductors , 2018, Materials & Design.

[16]  S. Zinkle,et al.  Influence of mechanical alloying and extrusion conditions on the microstructure and tensile properties of Low-Cr ODS FeCrAl alloys , 2018, Journal of Nuclear Materials.

[17]  A. Macháčková,et al.  Texture and residual stress within rotary swaged Cu/Al clad composites , 2018, Materials Letters.

[18]  F. Bergner,et al.  Why Do Secondary Cracks Preferentially Form in Hot-Rolled ODS Steels in Comparison with Hot-Extruded ODS Steels? , 2018, Crystals.

[19]  G. Odette,et al.  Texture evolution and microcracking mechanisms in as-extruded and cross-rolled conditions of a 14YWT nanostructured ferritic alloy , 2018, Acta Materialia.

[20]  L Kunčická,et al.  Deformation behaviour of Cu-Al clad composites produced by rotary swaging , 2018 .

[21]  M. Ghasemian,et al.  Investigation on microstructure and mechanical properties of Al/Al-Zn-Mg–Cu laminated composite fabricated by accumulative roll bonding (ARB) process , 2018 .

[22]  Chenyang Lu,et al.  Effects of Y2O3, La2O3 and CeO2 additions on microstructure and mechanical properties of 14Cr-ODS ferrite alloys produced by spark plasma sintering , 2017 .

[23]  F. Šiška,et al.  Kinetic study of static recrystallization in an Fe–Al–O ultra-fine-grained nanocomposite , 2017 .

[24]  A. Macháčková,et al.  Study of structure and residual stresses in cold rotary swaged tungsten heavy alloy , 2017 .

[25]  M. Šofer,et al.  Improvement of mechanical and electrical properties of rotary swaged Al-Cu clad composites , 2017 .

[26]  W. Donner,et al.  Magnetic hardening of Fe 50 Co 50 by rotary swaging , 2017 .

[27]  Yisheng Zhang,et al.  Joining process for copper and aluminum tubes by rotary swaging method , 2017 .

[28]  K. Laha,et al.  Development of Oxide Dispersion Strengthened (ODS) Ferritic Steel Through Powder Forging , 2017, Journal of Materials Engineering and Performance.

[29]  J. Drahokoupil,et al.  Evolution of macroscopic elastic moduli of martensitic polycrystalline NiTi and NiTiCu shape memory alloys with pseudoplastic straining , 2017 .

[30]  M. Asgari,et al.  Non-equal channel angular pressing (NECAP) of AZ80 Magnesium alloy: Effects of process parameters on strain homogeneity, grain refinement and mechanical properties , 2016 .

[31]  M. Šofer,et al.  Cold rotary swaging of a tungsten heavy alloy: numerical and experimental investigations , 2016 .

[32]  P. Král,et al.  Effect of strain path on severely deformed aluminium , 2016 .

[33]  T. Lowe,et al.  Synthesis of an Al/Al2O3 composite by severe plastic deformation , 2015 .

[34]  L. Wagner,et al.  Microstructure, Mechanical, and Fatigue Strength of Ti-54M Processed by Rotary Swaging , 2015, Journal of Materials Engineering and Performance.

[35]  F. G. Cuevas,et al.  A One-Dimensional Model of the Electrical Resistance Sintering Process , 2015, Metallurgical and Materials Transactions A.

[36]  A. Macháčková,et al.  Twist channel multi-angular pressing (TCMAP) as a new SPD process: Numerical and experimental study , 2014 .

[37]  M. Serrano,et al.  On anisotropy of ferritic ODS alloys , 2014 .

[38]  T. Byun,et al.  Fracture behavior of 9Cr nanostructured ferritic alloy with improved fracture toughness , 2014 .

[39]  K. Kurzydłowski,et al.  Evaluation of Microstructure and Mechanical Properties of Nano-Y2O3-Dispersed Ferritic Alloy Synthesized by Mechanical Alloying and Consolidated by High-Pressure Sintering , 2013, Metallurgical and Materials Transactions A.

[40]  Z. Oksiuta.  High-temperature oxidation resistance of ultrafine-grained 14 %Cr ODS ferritic steel , 2013, Journal of Materials Science.

[41]  J. Kim,et al.  Temperature dependence of strengthening mechanisms in the nanostructured ferritic alloy 14YWT: Part I—Mechanical and microstructural observations , 2013 .

[42]  A. Macháčková,et al.  Comparison of strain and stress conditions in conventional and ARB rolling processes , 2012 .

[43]  A. Macháčková,et al.  FEA of plastic flow in AZ63 alloy during ECAP process , 2012 .

[44]  J. B. Correia,et al.  Microstructural characterization of the ODS Eurofer 97 EU-batch , 2011 .

[45]  A. Dlouhý,et al.  The influence of imposed strain on the development of microstructure and transformation characteristics of Ni–Ti shape memory alloys , 2011 .

[46]  J. Fiala,et al.  Investigation of influence of preparation and heat treatment on deformation behaviour of the alloy NiTi after ECAE , 2009 .

[47]  F. G. Cuevas,et al.  Influence of milling media on the microstructure and mechanical properties of mechanically milled and sintered aluminium , 2005 .

[48]  P. Lukas,et al.  Creep deformation modelling of superalloy single crystals , 2000 .

[49]  P. Lukas,et al.  Model of creep in (001)-oriented superalloy single crystals , 1998 .

[50]  A. Argon,et al.  Directional coarsening in nickel-base single crystals with high volume fractions of coherent precipitates , 1994 .

[51]  Joachim Rösler,et al.  A new model-based creep equation for dispersion strengthened materials , 1990 .