Water cooling based strategy for lithium ion battery pack dynamic cycling for thermal management system

Abstract To investigate the thermal performance of water cooling based battery thermal management system in lithium ion batteries dynamic cycling, the experimental and numerical studies are carried out in this work. In numerical simulation, an electrochemical-thermal model is adopted to predict the thermal behavior and validates with experimental measurement. For both experimental and simulated results, the voltage, current, and the temperature distribution in the single battery and battery pack are exhibited. In addition, the active water cooling system is the better method to improve the battery pack thermal performance at low cycling rate. Moreover, dealing with the situation of using battery pack in wide range at different rate, a compound system need to be design in the real battery pack system.

[1]  Yanlai Zhang,et al.  Simulation of heat dissipation with phase change material for cylindrical power battery , 2012 .

[2]  Jaeshin Yi,et al.  Modelling the thermal behaviour of a lithium-ion battery during charge , 2011 .

[3]  John Newman,et al.  A General Energy Balance for Battery Systems , 1984 .

[4]  Mohammadhosein Safari,et al.  Analysis of lithium deinsertion/insertion in LiyFePO4 with a simple mathematical model , 2010 .

[5]  Anthony Jarrett,et al.  Design optimization of electric vehicle battery cooling plates for thermal performance , 2011 .

[6]  J. Bernard,et al.  Simplified Electrochemical and Thermal Model of LiFePO4-Graphite Li-Ion Batteries for Fast Charge Applications , 2012 .

[7]  Ahmad Pesaran,et al.  Battery thermal models for hybrid vehicle simulations , 2002 .

[8]  Jinhua Sun,et al.  Heat transfer in the dynamic cycling of lithium–titanate batteries , 2016 .

[9]  Lip Huat Saw,et al.  Numerical analyses on optimizing a heat pipe thermal management system for lithium-ion batteries during fast charging , 2015 .

[10]  Qingsong Wang,et al.  Numerical study on the thermal performance of a composite board in battery thermal management system , 2016 .

[11]  Xiangming He,et al.  Electro-thermal modeling and experimental validation for lithium ion battery , 2012 .

[12]  Ralph E. White,et al.  Thermal Model for a Li-Ion Cell , 2008 .

[13]  Li Lin,et al.  Modeling team member characteristics for the formation of a multifunctional team in concurrent engineering , 2004, IEEE Transactions on Engineering Management.

[14]  Qingsong Wang,et al.  Experimental study on the application of phase change material in the dynamic cycling of battery pack system , 2016 .

[15]  Srinivas Garimella,et al.  Passive, internal thermal management system for batteries using microscale liquid–vapor phase change , 2013 .

[16]  Rui Zhao,et al.  An experimental study of heat pipe thermal management system with wet cooling method for lithium ion batteries , 2015 .

[17]  M. Shui,et al.  GITT studies on oxide cathode LiNi1/3Co1/3Mn1/3O2 synthesized by citric acid assisted high-energy ball milling , 2013, Bulletin of Materials Science.

[18]  A. Elgafy,et al.  Numerical Study for Enhancing the Thermal Conductivity of Phase Change Material (PCM) Storage using High Thermal Conductivity Porous Matrix , 2005 .

[19]  Xianguo Li,et al.  Thermal management of lithium‐ion batteries for electric vehicles , 2013 .

[20]  Ya-Ling He,et al.  Internal cooling of a lithium-ion battery using electrolyte as coolant through microchannels embedded inside the electrodes , 2015 .

[21]  S. C. Chen,et al.  Thermal analysis of lithium-ion batteries , 2005 .

[22]  Ziping Feng,et al.  Thermal management performances of PCM/water cooling-plate using for lithium-ion battery module based on non-uniform internal heat source , 2017 .

[23]  M. Behm,et al.  Electrochemical characterisation and modelling of the mass transport phenomena in LiPF6–EC–EMC electrolyte , 2008 .

[24]  Jihong Wang,et al.  Overview of current development in electrical energy storage technologies and the application potential in power system operation , 2015 .