Development of a measurement metric for manufacturing process robustness

Literature on the study on manufacturing process robustness is limited. Very often, process robustness is dealt with single-stage process and considers a single response variable. Moreover, the effect of operators and equipment on the overall process robustness is seldom studied. These shortcomings have led to the development of a new measurement metric for evaluating manufacturing process robustness which is presented in this study. The proposed metric considers the effects of input raw material, process operating conditions and equipment and operator performances in its development. The metric can be used for analysing both univariate and multivariate data. Partial contribution indices and multivariate S/N ratio are also developed. Three case studies were conducted in centrifugal casting, heat treatment and forging shops. From the results, it is also clear that when the robustness of a process increases, the multivariate S/N ratio increases and the transmitted variation reduces.

[1]  D. Simpson,et al.  Robustness of modelled ozone exposures and doses. , 2007, Environmental pollution.

[2]  Genichi Taguchi.  System Of Experimental Design: Engineering Methods To Optimize Quality And Minimize Costs , 1987 .

[3]  Shiyu Zhou,et al.  Robust Method of Multiple Variation Sources Identification in Manufacturing Processes For Quality Improvement , 2006 .

[4]  A Hasman,et al.  Robustness metrics for measuring the influence of additive noise on the performance of statistical classifiers. , 1997, International journal of medical informatics.

[5]  Fred A. Spiring,et al.  A multivariate measure of process capability , 1991 .

[6]  Age K. Smilde,et al.  Introduction of a robustness coefficient in optimization procedures: Implementation in mixture design problems: Part I: Theory , 1990 .

[7]  M. Hulme,et al.  Assessing the robustness of adaptation decisions to climate change uncertainties: A case study on water resources management in the East of England , 2007 .

[8]  Véronique Bellon-Maurel,et al.  Robustness of models developed by multivariate calibration. Part I: The assessment of robustness , 2004 .

[9]  James M. Lucas,et al.  How to Achieve a Robust Process Using Response Surface Methodology , 1994 .

[10]  Shahram Shadrokh,et al.  Bi-objective resource-constrained project scheduling with robustness and makespan criteria , 2006, Appl. Math. Comput..

[11]  Eisenhower C. Etienne,et al.  The analysis and evaluation of a quality system using the Six Sigma benchmark: evidence for the robustness of Six Sigma processes , 2009 .

[12]  Christian N. Madu,et al.  Design optimization using signal-to-noise ratio , 1999, Simul. Pract. Theory.

[13]  Ihsan Sabuncuoglu,et al.  Hedging production schedules against uncertainty in manufacturing environment with a review of robustness and stability research , 2009, Int. J. Comput. Integr. Manuf..

[14]  Jhareswar Maiti,et al.  Implementing Mahalanobis-Taguchi system to improve casting quality in grey iron foundry , 2008 .

[15]  Miguel Valcárcel,et al.  Robustness in qualitative analysis: a practical approach , 2006 .

[16]  J. L Lin,et al.  The use of the orthogonal array with grey relational analysis to optimize the electrical discharge machining process with multiple performance characteristics , 2002 .

[17]  Xiaoping Du,et al.  Robust Mechanism synthesis with random and interval variables , 2009 .

[18]  S. Kim,et al.  Optimization of manufacturing parameters for a brake lining using Taguchi method , 2003 .

[19]  Age K. Smilde,et al.  Robustness of analytical chemical methods and pharmaceutical technological products. , 1996 .

[20]  Sridhar Seshadri,et al.  Robust Analysis of Variance: Process Design and Quality Improvement , 2005 .

[21]  Roberto Solis-Oba,et al.  Efficient algorithms for robustness in resource allocation and scheduling problems , 2006, Theor. Comput. Sci..

[22]  Richard A. Johnson,et al.  Applied Multivariate Statistical Analysis , 1983 .

[23]  Makarand S. Kulkarni,et al.  Combined Taguchi and dual response method for optimization of a centerless grinding operation , 2003 .

[24]  Karen A. F. Copeland.  Design and Analysis of Experiments, 5th Ed. , 2001 .

[25]  C. Fung,et al.  Multi-response optimization in friction properties of PBT composites using Taguchi method and principle component analysis , 2005 .

[26]  R. Ramakrishnan,et al.  Multi response optimization of wire EDM operations using robust design of experiments , 2006 .

[27]  Kevin Otto,et al.  Manufacturing System Robustness Through Integrated Modeling , 2001 .

[28]  James M. Lucas,et al.  Designs of mixed resolution for process robustness studies , 1997 .

[29]  Bieke Dejaegher,et al.  The variance of screening and supersaturated design results as a measure for method robustness , 2005 .

[30]  W.G. Hansen,et al.  Optimising Multivariate Calibration by Robustness Criteria , 2001 .

[31]  James W. Liddy,et al.  A note on multivariate capability indices , 1993 .

[32]  S. J. Hu,et al.  Robustness evaluation for compliant assembly systems , 2003 .

[33]  J. A. Robinson,et al.  Analysis of Variation Transmission in Manufacturing Processes—Part I , 1999 .

[34]  Luis Cuadros Rodríguez,et al.  A new approach to a complete robustness test of experimental nominal conditions of chemical testing procedures for internal analytical quality assessment , 1998 .

[35]  Mikkel T. Jensen,et al.  Improving robustness and flexibility of tardiness and total flow-time job shops using robustness measures , 2001, Appl. Soft Comput..

[36]  Lutgarde M. C. Buydens,et al.  Strategy for constructing robust multivariate calibration models , 1999 .

[37]  T. R. Bement,et al.  Taguchi techniques for quality engineering , 1995 .

[38]  B. Bhattacharyya,et al.  Parametric analysis and optimization of wire electrical discharge machining of γ-titanium aluminide alloy , 2005 .

[39]  Jack W. Baker,et al.  On the assessment of robustness , 2008 .