3D modeling of plasma-particle interactions in a plasma jet under dense loading conditions

Abstract A turbulent argon plasma jet discharged into an air atmosphere is modeled for given torch input parameters. Plasma–particle interactions are also modeled by coupling Lagrangian equations describing velocity, temperature and position of the particles with an Eulerian system of equations describing the plasma flow and temperature. Results of present model are compared with both experimental and previous model results. The effects of radial injection of carrier gas and particle loading both on the plasma and particle velocities and on the temperatures are clarified. Particle loading with carrier gas locally and strongly influences the flow fields of the plasma jet. A higher mass flow rate of the carrier gas decreases the axial velocity of the plasma jet locally. In swirl jet, the weak effects of carrier gas and particle loading are distributed in larger volume. It is found that both particle velocity and temperature distributions are wider at higher particle loading than at lower particle loading in non-swirl plasma jet.

[1]  V. Sobolev,et al.  In-flight behaviour of steel particles during plasma spraying , 1999 .

[2]  R. Sivakumar,et al.  Modelling of the temperature and the velocity of ceramic powder particles in a plasma flame—I. Alumina , 1990 .

[3]  Xi Chen,et al.  Three-dimensional simulation of a plasma jet with transverse particle and carrier gas injection , 2001 .

[4]  J. D. Ramshaw,et al.  Numerical simulations of argon plasma jets flowing into cold air , 1993 .

[5]  C. Coddet,et al.  Numerical study of an ArH2 gas mixture flowing inside and outside a dc plasma torch , 1998 .

[6]  P. Fauchais,et al.  Heat Generation and Particle Injection in a Thermal Plasma Torch , 1998 .

[7]  P. Proulx,et al.  Modelling of the plasma-particle interactions in a plasma jet , 1999 .

[8]  Y. Lee,et al.  Particle dynamics and particle heat and mass transfer in thermal plasmas. Part I. The motion of a single particle without thermal effects , 1985 .

[9]  E. Pfender,et al.  Particle dynamics and particle heat and mass transfer in thermal plasmas. Part III. Thermal plasma jet reactors and multiparticle injection , 1987 .

[10]  V. Prasad,et al.  Model and powder particle heating, melting, resolidification, and evaporation in plasma spraying processes , 1999 .

[11]  I. Ahmed,et al.  Simulation of Thermal Plasma Spraying of Partially Molten Ceramics: Effect of Carrier Gas on Particle Deposition and Phase Change Phenomena , 2000, Heat Transfer: Volume 3.

[12]  Maher I. Boulos,et al.  Thermal Plasmas: Fundamentals and Applications , 1994 .

[13]  R. Spores.  Analysis of the Flow Structure of a Turbulent Thermal Plasma Jet. , 1989 .

[14]  E. Pfender,et al.  Heat transfer to a single particle exposed to a thermal plasma , 1982 .

[15]  E. Pfender.  Particle behavior in thermal plasmas , 1989 .

[16]  R. L. Williamson,et al.  A Computational Examination of the Sources of Statistical Variance in Particle Parameters During Thermal Plasma Spraying , 2000 .

[17]  Julian Szekely,et al.  Some perspectives on the modeling of plasma jets , 1987 .

[18]  V. Prasad,et al.  Modeling and visualization of plasma spraying of functionally graded materials and its application to the optimization of spray conditions , 2001 .

[19]  A. Vardelle,et al.  Comparison of plasma-sprayed coatings produced in argon or nitrogen atmosphere , 1998 .

[20]  Xi Chen,et al.  Three-Dimensional Modeling of the Turbulent Plasma Jet Impinging upon a Flat Plate and with Transverse Particle and Carrier-Gas Injection , 2002 .

[21]  P. Proulx,et al.  Particle turbulent dispersion and loading effects in an inductively coupled radio frequency plasma , 2000 .

[22]  T. L. Bergman,et al.  Three-dimensional simulation of thermal plasma spraying of partially molten ceramic agglomerates , 2000 .