Thermo-elastohydrodynamic analysis of connecting rod bearing in internal combustion engine

A comprehensive method of thermo-elastohydrodynamic lubrication analysis for connecting rod bearings is proposed, which includes thermal distortion as well as elastic deformation of the hearing surface. Lubrication film temperature is treated as a time-dependent two-dimensional variable which is averaged over the film thickness, while the bearing temperature is assumed to be time-independent and three-dimensional. It is assumed that a portion of the heat generated by viscous dissipation in the lubrication film is absorbed by the film itself, and the remainder flows into the bearing structure. Massconserving cavitation algorithm is applied, and the effect of variable viscosity is included in the Reynolds equation. Simulation results of the connecting rod bearing of an internal combustion engine are presented. It is shown that the predicted level of the thermal distortion is as large as that of the elastic deformation and the bearing clearance, and that the thermal distortion has remarkable effects on the bearing performance. Therefore, the thermo-elastohydrodynamic lubrication analysis is strongly recommended to predict the performance of connecting rod bearings in internal combustion engines.

[1]  J. F. Booker,et al.  A Finite Element Cavitation Algorithm: Application/Validation , 1991 .

[2]  Jean Frene,et al.  Comparison of Dynamic Behavior of Elastic Connecting-Rod Bearing in Both Petrol and Diesel Engines , 1985 .

[3]  E. H. Smith,et al.  A New Approach to the Solution of Elastohydrodynamic Lubrication of Crankshaft Bearings , 1990 .

[4]  Dong-Chul Han,et al.  Oil film thickness in engine connecting-rod bearing with consideration of thermal effects : Comparison between theory and experiment , 1999 .

[5]  J. F. Booker,et al.  A Finite Element Cavitation Algorithm , 1991 .

[6]  L. van der Tempel,et al.  Starvation in Dynamically Loaded Flexible Short Journal Bearings , 1985 .

[7]  Chao Zhang,et al.  A transient thermohydrodynamic analysis of dynamically loaded finite journal bearings with rough surface including mass conserving cavitation , 1999 .

[8]  E. H. Smith.  Paper IV(iii) – Temperature variations in crankshaft bearings , 1993 .

[9]  J. F. Booker.  Erratum: “Dynamically-Loaded Journal Bearings: Numerical Application of the Mobility Method” (Journal of Lubrication Technology, 1971, 93, pp. 168–176) , 1971 .

[10]  H Xu.  Recent advances in engine bearing design analysis , 1999 .

[11]  J. F. Booker,et al.  Dynamically-Loaded Journal Bearings: Numerical Application of the Mobility Method , 1971 .

[12]  J. D. C. McIvor,et al.  Finite Element Analysis of Dynamically Loaded Flexible Journal Bearings: A Fast Newton-Raphson Method , 1989 .

[13]  Stephen Boedo,et al.  Surface Roughness and Structural Inertia in a Mode-Based Mass-Conserving Elastohydrodynamic Lubrication Model , 1997 .

[14]  Dominique Bonneau,et al.  EHD Analysis, Including Structural Inertia Effects and a Mass-Conserving Cavitation Model , 1995 .

[15]  P. P. Love,et al.  Paper 4: Bearings for Reciprocating Machinery: A Review of the Present State of Theoretical, Experimental and Service Knowledge , 1967 .

[16]  Taeyoung Han,et al.  A Transient Thermohydrodynamic Analysis Including Mass Conserving Cavitation for Dynamically Loaded Journal Bearings , 1995 .

[17]  H. Moes,et al.  Thermal Effects in Dynamically Loaded Flexible Journal Bearings , 1989 .

[18]  Joel H. Ferziger,et al.  Introduction to Theoretical and Computational Fluid Dynamics , 1996 .

[19]  P. K. Goenka,et al.  The Elastohydrodynamic Solution of Journal Bearings Under Dynamic Loading , 1985 .

[20]  D. Souchet,et al.  Influence of Thermal and Elastic Deformations on Connecting-Rod Big End Bearing Lubrication Under Dynamic Loading , 2000 .

[21]  J. F. Booker,et al.  Modal Analysis of Elastohydrodynamic Lubrication: A Connecting Rod Application , 1990 .

[22]  K. P. Oh.  The Numerical Solution of Dynamically Loaded Elastohydrodynamic Contact as a Nonlinear Complementarity Problem , 1984 .