Selective laser melting of stainless-steel/nano-hydroxyapatite composites for medical applications: Microstructure, element distribution, crack and mechanical properties

Abstract This paper presents a study on the layer-by-layer synthesis of stainless-steel (SS) and nano-hydroxyapatite (nHA) composite using selective laser melting (SLM). The microstructural and elemental examinations, tensile and nanoindentation tests were conducted. The effects of material ratios and laser scanning speeds on cracks and pores were identified by the cross-section morphology of samples fabricated by SLM. High content of nHA resulted in the particle aggregation at the melt pool boundaries and the cracks on these areas. Increasing in laser scanning speed shortened the solidification time of melt pools, thus withstood aggregation of nHA and decreased the degree of cracks. Optimum material ratio and laser scanning speed were determined for SLM of SS/nHA composite in order to fabricate load-bearing bone implants. A uniform distribution of Ca and P elements was detected on the top surfaces of as-SLM fabricated composite, which could facilitate good bone osseointegration. The highest tensile strength, elastic modulus and hardness of SS/nHA samples produced at optimum processing condition were found to be higher than that of the human bone, which provides the possibility to fabricate SS/nHA porous scaffolds with tailored mechanical properties for load-bearing bone applications.

[1]  Jacqueline Lecomte-Beckers,et al.  Mechanical properties of alloy Ti–6Al–4V and of stainless steel 316L processed by selective laser melting: Influence of out-of-equilibrium microstructures , 2014 .

[2]  T. Hanawa,et al.  Hydrothermal modification of titanium surface in calcium solutions. , 2002, Biomaterials.

[3]  H. Man,et al.  Laser cladding of HA/Ti composite coating on NiTi alloy , 2013 .

[4]  J. Parvizi,et al.  Do Tantalum and Titanium Cups Show Similar Results in Revision Hip Arthroplasty? , 2010, Clinical orthopaedics and related research.

[5]  W. Kurz,et al.  SINGLE-CRYSTAL LASER DEPOSITION OF SUPERALLOYS: PROCESSING-MICROSTRUCTURE MAPS , 2001 .

[6]  Wei Qingsong,et al.  Effect of molten pool boundaries on the mechanical properties of selective laser melting parts , 2014 .

[7]  Recep Gümrük,et al.  Static mechanical behaviours of stainless steel micro-lattice structures under different loading conditions , 2013 .

[8]  G. Pharr,et al.  An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments , 1992 .

[9]  Weidong Huang,et al.  Microstructure and residual stress of laser rapid formed Inconel 718 nickel-base superalloy , 2011 .

[10]  M. Fathi,et al.  Preparation and bioactivity evaluation of bone-like hydroxyapatite nanopowder , 2008 .

[11]  Liang Hao,et al.  Selective laser melting of a stainless steel and hydroxyapatite composite for load-bearing implant development , 2009 .

[12]  Konrad Wissenbach,et al.  Additive manufacturing of ZrO2-Al2O3 ceramic components by selective laser melting , 2013 .

[13]  Chilukuri Ramesh,et al.  Abrasive wear behaviour of laser sintered iron–SiC composites , 2009 .

[14]  C. Beythien,et al.  In vitro analyses of diamond-like carbon coated stents. Reduction of metal ion release, platelet activation, and thrombogenicity. , 2000, Thrombosis research.

[15]  Gary J. Cheng,et al.  Laser engineered multilayer coating of biphasic calcium phosphate/titanium nanocomposite on metal substrates. , 2011, ACS Applied Materials and Interfaces.

[16]  Lijuan Kang,et al.  Functionally graded carbon nanotubes/hydroxyapatite composite coating by laser cladding , 2011 .

[17]  K. Osakada,et al.  The manufacturing of hard tools from metallic powders by selective laser melting , 2001 .

[18]  J A McGeough,et al.  Age-related changes in the tensile properties of cortical bone. The relative importance of changes in porosity, mineralization, and microstructure. , 1993, The Journal of bone and joint surgery. American volume.

[19]  Richard M. Everson,et al.  Finite element simulation of the temperature and stress fields in single layers built without-support in selective laser melting , 2013 .

[20]  K. Mensah-Darkwa,et al.  Mechanical and Corrosion Properties of Magnesium–Hydroxyapatite (Mg–HA) Composite Thin Films , 2013 .

[21]  I. Yadroitsev,et al.  Selective laser sintering/melting of nitinol–hydroxyapatite composite for medical applications , 2011 .

[22]  P. Lipinski,et al.  Development and mechanical characterization of porous titanium bone substitutes. , 2012, Journal of the mechanical behavior of biomedical materials.

[23]  J. Kruth,et al.  Residual stresses in selective laser sintering and selective laser melting , 2006 .

[24]  Yee-Hsien Ho,et al.  Laser coating of hydroxyapatite on Mg for enhanced physiological corrosion resistance and biodegradability , 2012 .

[25]  Mika Salmi,et al.  Patient‐specific reconstruction with 3D modeling and DMLS additive manufacturing , 2012 .

[26]  J. Kruth,et al.  Assessing and comparing influencing factors of residual stresses in selective laser melting using a novel analysis method , 2012 .

[27]  Caterina Casavola,et al.  Preliminary investigation on distribution of residual stress generated by the selective laser melting process , 2009 .

[28]  X. Miao.  Observation of microcracks formed in HA-316L composites , 2003 .

[29]  M. Fathi,et al.  In vitro corrosion behavior of bioceramic, metallic, and bioceramic-metallic coated stainless steel dental implants. , 2003, Dental materials : official publication of the Academy of Dental Materials.

[30]  Masahiro Yoshimura,et al.  Processing and properties of hydroxyapatite-based biomaterials for use as hard tissue replacement implants , 1998 .

[31]  Andrey V. Gusarov,et al.  Residual Stresses at Laser Surface Remelting and Additive Manufacturing , 2011 .

[32]  L. Murr,et al.  Microstructures and mechanical behavior of Inconel 718 fabricated by selective laser melting , 2012 .

[33]  Myer Kutz,et al.  Standard Handbook of Biomedical Engineering and Design , 2002 .

[34]  Akira Hosokawa,et al.  Residual Stress and Deformation of Consolidated Structure Obtained by Layered Manufacturing Process , 2013 .