Experimental, statistical, and numerical investigations for influence of using vegetable oil with mineral oil to enhance the flow characteristics through a closed hydraulic circuit

[1]  G. Anand,et al.  Performance optimization by study of tribological and rheological properties of dates oil with graphene oxide nano-additives , 2022, Biofuels.

[2]  A. Khadom,et al.  Experimental validation and numerical investigation for optimization and evaluation of heat transfer enhancement in double coil heat exchanger , 2021 .

[3]  H. Öğüt,et al.  The effects of the use of vegetable oil based as engine lubrication oil on engine performance and emissions in diesel engines , 2020, Energy Sources, Part A: Recovery, Utilization, and Environmental Effects.

[4]  Hameed B. Mahood,et al.  Experimental study on the melting behavior of a phase change material in a conical coil latent heat thermal energy storage unit , 2020, Applied Thermal Engineering.

[5]  J. Stokes,et al.  Improving tribological properties of oil-based lubricants using hybrid colloidal additives , 2020 .

[6]  Hameed B. Mahood,et al.  Effect of fin geometry on natural convection heat transfer in electrical distribution transformer: Numerical study and experimental validation , 2019 .

[7]  M. G. Rasteiro,et al.  Oil/water stratified flow in a horizontal pipe: Simulated and experimental studies using EIT , 2019, Journal of Petroleum Science and Engineering.

[8]  A. Azdarpour,et al.  The hydrodynamic behavior of high viscous oil-water flow through horizontal pipe undergoing sudden expansion—CFD study and experimental validation , 2018, Chemical Engineering Research and Design.

[9]  G. Sriram,et al.  Synthesis, characterisation and tribological investigation of vegetable oil-based pentaerythryl ester as biodegradable compressor oil , 2018, Industrial Crops and Products.

[10]  A. Hoang,et al.  A study of emission characteristic, deposits, and lubrication oil degradation of a diesel engine running on preheated vegetable oil and diesel oil , 2018, Energy Sources, Part A: Recovery, Utilization, and Environmental Effects.

[11]  Lei Zheng,et al.  Fatty acid based phosphite ionic liquids as multifunctional lubricant additives in mineral oil and refined vegetable oil , 2018, Tribology International.

[12]  Juraj Tulík,et al.  The comparison of biodegradable hydraulic fluid with mineral oil on the basis of selected parameters. , 2018 .

[13]  E. Burlutskii.  CFD study of oil-in-water two-phase flow in horizontal and vertical pipes , 2017 .

[14]  H. Yeung,et al.  CFD simulation of horizontal oil-water flow with matched density and medium viscosity ratio in different flow regimes , 2017 .

[15]  Samion Syahrullail,et al.  Suitable additives for vegetable oil‐based automotive shock absorber fluids: an overview , 2016 .

[16]  M. Ali,et al.  Enhancing the thermophysical properties and tribological behaviour of engine oils using nano-lubricant additives , 2016 .

[17]  T. Jen,et al.  The influence of fatty acids on tribological and thermal properties of natural oils as sustainable biolubricants , 2015 .

[18]  K. Nair,et al.  A comparative study of polymeric additives as biodegradable viscosity boosters for biolubricant formulations , 2015 .

[19]  A. S. Olawale,et al.  Experimental investigation on flow patterns and pressure gradient through two pipe diameters in horizontal oil–water flows , 2014 .

[20]  A. Khadom,et al.  Performance of polyacrylamide as drag reduction polymer of crude petroleum flow , 2014 .

[21]  I. Hussein,et al.  Pressure drop reduction of stable water-in-oil emulsions using organoclays , 2014 .

[22]  Haji Hassan Masjuki,et al.  The prospects of biolubricants as alternatives in automotive applications , 2014 .

[23]  A. Khadom,et al.  Studying the Effect of Some Surfactants on Drag Reduction of Crude Oil Flow , 2013 .

[24]  V. Vozárová,et al.  Influence of Temperature on Energetic and Rheological Characteristics of PLANTOHYD Bio Lubricants – a Study in the Laboratory , 2013 .

[25]  Debora Fino,et al.  LCA of petroleum-based lubricants: state of art and inclusion of additives , 2012, The International Journal of Life Cycle Assessment.

[26]  M. Farooq,et al.  The Study of Wear Behaviour of 12-hydroxystearic acid in Vegetable Oils , 2011 .

[27]  Y. M. Shashidhara,et al.  Vegetable oils as a potential cutting fluid—An evolution , 2010 .

[28]  M. A. Fazal,et al.  Effect of temperature on tribological properties of palm biodiesel , 2010 .

[29]  Thomas S.Y. Choong,et al.  Numerical study of dispersed oil–water turbulent flow in horizontal tube , 2009 .

[30]  N. H. Jayadas,et al.  Tribological evaluation of coconut oil as an environment-friendly lubricant , 2007 .

[31]  Sevim Z. Erhan,et al.  Oxidation and low temperature stability of vegetable oil-based lubricants , 2006 .

[32]  S. Boyde.  Green lubricants. Environmental benefits and impacts of lubrication , 2002 .

[33]  Md. Abdul Maleque,et al.  Effect of mechanical factors on tribological properties of palm oil methyl ester blended lubricant , 2000 .

[34]  Haji Hassan Masjuki,et al.  Palm oil and mineral oil based lubricants—their tribological and emission performance , 1999 .

[35]  Karl P. Jr. Kammann,et al.  Sulfurized vegetable oil products as lubricant additives , 1985 .

[36]  Sergejus Lebedevas,et al.  Oxidation stability of biofuel containing Camelina sativa oil methyl esters and its impact on energy and environmental indicators of diesel engine , 2013 .

[37]  Wilfried J. Bartz,et al.  Lubricants and the environment , 1998 .