Preparation of ceramic foam spheres by injection molding of emulsions

ABSTRACT An emulsion-based injection molding process has been reported for the preparation of ceramic foam spheres from kaolin and alumina. The foam spheres produced from kaolin alone cracked during sintering due to extensive shrinkage and an excessive glass phase. Incorporation of a minimum of 10 wt% alumina in kaolin prevented the cracking of foam spheres during sintering by promoting secondary mullite growth, which decreases both the glass phase concentration and sintering shrinkage. Foam spheres with an interconnected cellular structure having open porosities, average cell sizes and diametrical compressive strengths in the ranges of 76.5 to 82.7 vol.%, 6.8 to 9.2 μm and 1.65 to 0.93 MPa, respectively, were produced from emulsions prepared from hydrogenated vegetable oil and aqueous clay slurries. The interconnected open cell structure and small cell size enabled fast absorption and 100% retention of urea solution for N2O4 scrubber application. The urea solution absorption capacity (71.5 to 80 vol.%) of the foam spheres was much higher than the capacity (45.6 vol.%) of the porous clay ceramic media currently used in N2O4 scrubbers.

[1]  Jinlong Yang,et al.  Ultralight alumina ceramic foams with single-grain wall using sodium dodecyl sulfate as long-chain surfactant , 2016 .

[2]  Shan Qiu,et al.  Freeze cast fabrication of porous ceramics using tert-butyl alcohol–water crystals as template , 2016 .

[3]  S. Vijayan,et al.  Effect of emulsion composition on gel strength and porosity in the preparation of macroporous alumina ceramics by freeze gelcasting , 2015 .

[4]  S. Vijayan,et al.  Freeze gelcasting of hydrogenated vegetable oil-in-aqueous alumina slurry emulsions for the preparation of macroporous ceramics , 2014 .

[5]  Jang-Hoon Ha,et al.  Particle-stabilized ultra-low density zirconia toughened alumina foams , 2013 .

[6]  X. Xi,et al.  Processing and Properties of Porous PZT Ceramics from Particle‐Stabilized Foams via Gel Casting , 2013 .

[7]  J. Abrantes,et al.  Cellular ceramics processed by paraffin emulsified suspensions with collagen consolidation , 2013 .

[8]  L. Gibson,et al.  Development and mechanical characterization of novel ceramic foams fabricated by gel-casting , 2013 .

[9]  Liu Qiang,et al.  Fabrication of gradient porous β-SiAlON ceramics via a camphene-based freeze casting process , 2012 .

[10]  Jinlong Yang,et al.  Pore structure control of Si3N4 ceramics based on particle-stabilized foams , 2012, Journal of Porous Materials.

[11]  I. Kim,et al.  Stabilization of Wet Foams for Porous Ceramics Using Amphiphilic Particles , 2011 .

[12]  Y. Shimizu,et al.  Fabrication of porous alumina ceramics having cell windows with controlled size by PMMA template method , 2010 .

[13]  W. Pabst,et al.  Elastic properties of porous oxide ceramics prepared using starch as a pore-forming agent , 2009 .

[14]  S. Barg,et al.  New cellular ceramics from high alkane phase emulsified suspensions (HAPES) , 2009 .

[15]  M. Potoczek,et al.  Manufacturing of highly porous calcium phosphate bioceramics via gel-casting using agarose , 2009 .

[16]  Z. Ahmad,et al.  Preparation and characterization of ceramic foam produced via polymeric foam replication method , 2008 .

[17]  S. Barg,et al.  Cellular ceramics by direct foaming of emulsified ceramic powder suspensions , 2008 .

[18]  L. Gauckler,et al.  Processing of Particle‐Stabilized Wet Foams Into Porous Ceramics , 2007 .

[19]  W. Pabst,et al.  Porous ceramics prepared using PoPPy seed as a pore-forming agent , 2007 .

[20]  Hyoun‐Ee Kim,et al.  Highly porous hydroxyapatite bioceramics with interconnected pore channels using camphene-based freeze casting , 2007 .

[21]  L. Gauckler,et al.  Tailoring the microstructure of particle-stabilized wet foams. , 2007, Langmuir : the ACS journal of surfaces and colloids.

[22]  Eduardo Saiz,et al.  Freeze casting of hydroxyapatite scaffolds for bone tissue engineering. , 2006, Biomaterials.

[23]  T. Moritz,et al.  Ceramic Bodies with Complex Geometries and Ceramic Shells by Freeze Casting Using Ice as Mold Material , 2006 .

[24]  A. Buekenhoudt,et al.  Silicon Carbide Foams by Polyurethane Replica Technique , 2005 .

[25]  J. Ferreira,et al.  Fabrication of Highly Porous Mullite Materials , 2005 .

[26]  M. Scheffler,et al.  Polysilsesquioxane derived ceramic foams with gradient porosity , 2005 .

[27]  P. Greil,et al.  LZSA glass ceramic foams prepared by replication process , 2005 .

[28]  S. Mullens,et al.  Strong ceramic foams from polyurethane templates , 2005 .

[29]  M. Hon,et al.  Phase transformation and growth of mullite in kaolin ceramics , 2004 .

[30]  F. Gnanam,et al.  Mullite from clay–reactive alumina for insulating substrate application , 2004 .

[31]  J. Richardson,et al.  Carbon dioxide reforming with Rh and Pt–Re catalysts dispersed on ceramic foam supports , 2003 .

[32]  S. Dhara,et al.  A Simple Direct Casting Route to Ceramic Foams , 2003 .

[33]  P. Colombo,et al.  SiOC Ceramic Foams through Melt Foaming of a Methylsilicone Preceramic Polymer , 2003 .

[34]  M. Edirisinghe,et al.  Porosity and Strength of Silicon Carbide Foams Prepared Using Preceramic Polymers , 2002 .

[35]  J. Koo,et al.  Evaluation of Porous Ceramic as Microbial Carrier of Biofilter to Remove Toluene Vapor , 2001, Environmental technology.

[36]  W. Tuan,et al.  Preparation of mullite by the reaction sintering of kaolinite and alumina , 2000 .

[37]  J. Richardson,et al.  Properties of ceramic foam catalyst supports: pressure drop , 2000 .

[38]  W. Tuan,et al.  Microstructural evolution of mullite during the sintering of kaolin powder compacts , 2000 .

[39]  J. Amigó,et al.  XRD microstructural analysis of mullites obtained from kaolinite–alumina mixtures , 2000 .

[40]  J. Moulijn,et al.  Ceramic foam as a potential molten salt oxidation catalyst support in the removal of soot from diesel exhaust gas , 1999 .

[41]  J. Binner,et al.  Processing of cellular ceramics by foaming and in situ polymerisation of organic monomers , 1999 .

[42]  K. Westberg.  Measurements of the Efficiency of a NASA/Air Force Alkaline Scrubber in Removing Waste NO2/N2O4 Vapors, , 1995 .

[43]  G. Thomas,et al.  Mullite formation in kaolinite-α-alumina , 1994 .

[44]  E. David.  Mechanical strength and reliability of the porous materials used as adsorbents/catalysts and the new development trends , 2015 .

[45]  Honglei Wang,et al.  Preparation of Si3N4 ceramic foams by simultaneously using egg white protein and fish collagen , 2013 .

[46]  E. Ewais,et al.  Processing of Open Porous Zirconia via Alkane‐Phase Emulsified Suspensions for Plasma Applications , 2011 .

[47]  L. Gauckler,et al.  Microstructural Control of Self-Setting Particle-Stabilized Ceramic Foams , 2011 .

[48]  I. Song,et al.  Processing and properties of polysiloxane-derived porous silicon carbide ceramics using hollow microspheres as templates , 2008 .

[49]  Udayan Senapati,et al.  Porcelain—Raw Materials, Processing, Phase Evolution, and Mechanical Behavior , 1998 .