Grain Orientation Optimization of Two-Dimensional Grain Selector during Directional Solidification of Ni-Based Superalloys

The grain selection method is widely used in industry to produce Ni-based single crystal superalloys. A Z-form two-dimensional (2D) grain selector was designed to obtain high-quality single crystals. To control grain orientation deviation, one of the most important defects of the single crystal superalloys in casting, Z-form 2D grain selectors with different take-off angle were investigated in this study. The MM247LC superalloy single crystal samples were obtained by the Bridgman method modified by the Z-form grain selectors in this study. The Electron Backscattered Diffraction (EBSD) and the Optical Microscopy (OM) were used to observe and measure the grain selection growth and the microstructural evolution and orientation of the single crystal were also discussed. The results show that a Z-form 2D grain selector with an appropriate take-off angle can significantly reduce the deviation of the grain orientation. A single crystal superalloy with a deviation angle less than 6° can be obtained effectively when the take-off angle was 40°.

[1]  R. Polvorosa,et al.  Surface integrity and fatigue of non-conventional machined Alloy 718 , 2019 .

[2]  A. Bührig-Polaczek,et al.  Grain Selection in a High-Efficiency 2D Grain Selector During Casting of Single-Crystal Superalloys , 2019, Materials.

[3]  A. Bührig-Polaczek,et al.  Development of a High-Efficiency Z-Form Selector for Single Crystal Blades and Corresponding Grain Selection Mechanism , 2019, Materials.

[4]  I. Steinbach,et al.  Rejuvenation of Single-Crystal Ni-Base Superalloy Turbine Blades: Unlimited Service Life? , 2018, Metallurgical and Materials Transactions A.

[5]  L. N. López de Lacalle,et al.  Tool wear on nickel alloys with different coolant pressures: Comparison of Alloy 718 and Waspaloy , 2017 .

[6]  J. Sieniawski,et al.  Control of liquidus isotherm shape during solidification of Ni-based superalloy of single crystal platforms , 2016 .

[7]  Andreas Bührig-Polaczek,et al.  Comparative Investigation of the Downward and Upward Directionally Solidified Single-Crystal Blades of Superalloy CMSX-4 , 2016, Metallurgical and Materials Transactions A.

[8]  Shu Yan Zhang,et al.  The role of stress relaxation and creep during high temperature deformation in Ni-base single crystal superalloys – Implications to strain build-up during directional solidification , 2016 .

[9]  H. Fu,et al.  The process analysis of seeding-grain selection and its effect on stray grain and orientation control , 2016 .

[10]  L. Lou,et al.  Effect of skew angle of holes on the tensile behavior of a Ni-base single crystal superalloy , 2015 .

[11]  E. Karamian,et al.  Characterization and Investigation of Grain Selection in Spiral Grain Selectors during Casting Single-Crystal Turbine Blades , 2015 .

[12]  H. Fu,et al.  Grain Selection During Casting Ni-Base, Single-Crystal Superalloys with Spiral Grain Selector , 2012, Metallurgical and Materials Transactions A.

[13]  H. Dai,et al.  Grain Selection in Spiral Selectors During Investment Casting of Single-Crystal Turbine Blades: Part I. Experimental Investigation , 2011 .

[14]  Z. Hu,et al.  Evolution of Grain Selection in Spiral Selector during Directional Solidification of Nickel-base Superalloys , 2011 .

[15]  J. Gebelin,et al.  Effect of spiral shape on grain selection during casting of single crystal turbine blades , 2009 .

[16]  M. Tamura,et al.  Analysis of single crystal casting process taking into account the shape of pigtail , 2005 .

[17]  Hongbiao Dong,et al.  Microscale simulation of stray grain formation in investment cast turbine blades , 2004 .

[18]  Toshiharu Kobayashi,et al.  Creep behaviour of Ni-base single-crystal superalloys with various γ' volume fraction , 2004 .

[19]  R. Napolitano,et al.  The convergence-fault mechanism for low-angle boundary formation in single-crystal castings , 2000 .

[20]  W. T. King,et al.  CARBON ADDITIONS AND GRAIN DEFECT FORMATION IN HIGH REFRACTORY NICKEL-BASE SINGLE CRYSTAL SUPERALLOYS , 2000 .

[21]  R. Arthey,et al.  Cost Effective Single Crystals , 1984 .

[22]  R. MacKay,et al.  The influence of orientation on the stress rupture properties of nickel-base superalloy single crystals , 1982 .